Goldfinch (oz17075)

 

Goldfinch (oz17075) by Bill Bowne 2026 - plan thumbnail

About this Plan

Goldfinch. Radio control sport biplane model. Wingspan 30.6 in, wing area 288 sq in, for electric power with Turnigy G2826 brushless motor.

Quote: "The Goldfinch is an update of my REM Perky design for a Traplet magazine (circa 2011). The main changes are a longer fuselage (1 in added aft of the wing) and ailerons on the top wing. The Perky was a bit nose-heavy and had a strange habit of locking into inverted flight when rudder-rolled; other than that, it flew fine. I was hoping that the longer fuse would help with nose-heaviness, and the ailerons would let the model do proper axial rolls - and I was right! The Goldfinch rolls as smoothly as most high-winged models and balances with the battery almost under the CG.

Goldfinch construction is pretty simple, provided you have a bit of experience building balsa models. About the only unique features are:

• Wings have identical dihedral and were built on the same jig. Center-section and one wing panel built first, then wing swapped around on jig and opposite panel added.
• Ply aileron control horn ribs aren’t added until the ailerons are framed up and cut from the wing
• 1/8” sq. balsa fuselage formers recessed 1/32” from skin by using 1/8 *1/32” ‘facing strips’ for smoother sides. If you prefer, use 1/32” scrap to lift the verticals so they’re flush with the facing strips.
• Model is covered with Ultracote (Profilm), ailerons are hinged with same material.
• Sew aluminum tubes to bulkheads LP3 and LP4, then slit near center. After you’re done covering, plug in the LG wires, then dribble some CA into the slits to lock the gear wires into place.
• Aft fuse top and bottom diagonals are reverse images of each other, but side diagonals are the same.
• Sheet top wing aileron bay TE and aileron LE with one strip, then slit aileron loose from below. Use bay TE strip as guide.

Basic stats:
Area: 288 in. sq. (total)
Span: 30.6” top, 26.6” bottom
Weight RTF: 19 oz.
Wing Loading: 9.4 oz./ft. sq.
Motor: DYS 2822-14
Prop: APC 6X4E
Battery: 3S1000 to 3S1300 Lipo
Servos: Two HXT 900 (9 gram, Rudder & Elevator), Two HXT 500 (5 gram, Ailerons)

Control throws (measured at surface’s widest part):
Rudder: + 5/8”
Elevator: + 3/8”
Ailerons (with differential)
Up: 1/2”
Down: 3/8”

Expo not used, but 20% rudder is mixed into the ailerons.

I found the Goldfinch drawing on-line and printed it onto a transparent Avery 5664 label; after that, I colored in the orange beak and white feathers with Sharpie pens on the REVERSE (sticky) side. "

Direct submission to Outerzone.

Quote: "Hi Steve & Mary, Here's my latest, a small cabin biplane I call the Goldfinch. 288 in. sq, weight ~19 oz, full-house radio. It's a fun little putterer: nicely aerobatic at full throttle, but a gentle putterer when the go stick is pulled back.

Plans were drawn on LibreCAD and are sized for a 36 X 48" sheet. Most of the build pictures are lost, so all I have are early shots and finished model shots.

Started drawing my next design, but that project should take a while as it's a much more complicated (albeit only slightly larger) biplane.

Sincerely,
Bill Bowne"

Supplementary file notes

Build notes.
Build pics.
Parts list.

CAD file

This plan is available for download in CAD format.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Goldfinch (oz17075) by Bill Bowne 2026 - model pic

Datafile:
  • (oz17075)
    Goldfinch
    by Bill Bowne
    2026 
    30in span
    Electric R/C Biplane Cabin
    clean :)
    all formers complete :)
  • Submitted: 06/10/2026
    Filesize: 782KB
    Format: • PDFvector • CADfile
    Credit*: BillBowne
    Downloads: 297

Goldfinch (oz17075) by Bill Bowne 2026 - pic 003.jpg
003.jpg
Goldfinch (oz17075) by Bill Bowne 2026 - pic 004.jpg
004.jpg
Goldfinch (oz17075) by Bill Bowne 2026 - pic 005.jpg
005.jpg
Goldfinch (oz17075) by Bill Bowne 2026 - pic 006.jpg
006.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • Goldfinch (oz17075)
  • Plan File Filesize: 782KB Filename: Goldfinch_oz17075.pdf
  • Supplement Filesize: 35KB Filename: Goldfinch_oz17075_build_notes.pdf
  • Supplement Filesize: 173KB Filename: Goldfinch_oz17075_build_pics.pdf
  • Supplement Filesize: 24KB Filename: Goldfinch_oz17075_parts_list.pdf
  • CAD Zip Filesize: 229KB Filename: Goldfinch_oz17075_cad.zip
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2026.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.