Rhonsperber (oz15519)

 

Rhonsperber (oz15519) by Werner Thies, Willi Rolf 1975 - plan thumbnail

About this Plan

Rhonsperber. Simple profile glider model. Wingspan 550 mm.

This plan appeared in the book "Flugmodelle Bauen und Einfliegen" by Werner Thies & Willi Rolf, 1975.

Direct submission to Outerzone.

Note see Ente (oz15512) for article (full chapter from the book).

Quote (google-translated): "Rhönsperber. The last of the small balsa gliders is again based on a large model. It is the 'Rhönsperber', which was designed in the early 1930s by the then most famous glider designer H Jacobs (Fig. 47, see Plate V, at the end of the volume). The experience gained up to that point in the field of gliding was largely utilized in the design of this aircraft model.

The fuselage of the fullsize Rhönsperber is made of a plywood tube that tapers slightly towards the back. The vertical fin grows harmoniously out of the fuselage and forms its end with the rudder. The horizontal tail unit is self-supporting. The gull wing, typical of many gliders of the time and reminiscent of a sailing seagull, is made up of a rectangle and a trapezoid in plan and has a wingspan of 15.3 m.

Considerable performance was achieved with the 'Rhönsperber' glider. Heinemann sailed from the Wasserkuppe to Brno (504 km). The famous glider pilot Hanna Reitsch spun from a height of 2475 m to 554 m in 2 minutes and 25 seconds with 42 revolutions.

The model is again largely true to the original; only the fuselage is designed as a flat fuselage for weight reasons and because it is easier. The construction hardly differs from that of the other models. Only the wing is a little more complex. It has a real profile; that is why we use 3 mm balsa wood for its construction.

After cutting out the two wing halves, the wing profile shown in the cross-section drawings is roughly pre-worked with a balsa plane or a sharp balsa knife and only then sanded with fine sandpaper. When it is correctly profiled, ie nicely rounded at the wing nose and tapering at the wing end, it is separated at the bends. The separation points are carefully sanded at the necessary angle and glued together with UHU-hard.

For this we absolutely need a 'slipway', which we can build with a few resources from a few small boards (Fig. 48). A strip of paper about 1 cm wide under the bends prevents the glider from sticking to the slipway and strengthens the bend considerably, especially if a similar strip is glued to the top. The horizontal and vertical stabilizers are cut from 1 mm balsa wood and glued to the fuselage. This too must be done very carefully. Any mistake, e.g. an incorrect setting angle of the horizontal stabilizer, leads to a deterioration in the flight characteristics.

The center of gravity of the finished model should be 16 mm behind the wing nose. We therefore attach enough lead to the nose of the fuselage until the model is supported and exactly level at this point. Because of its slightly higher weight, this model flies a little faster than the other gliders described so far. The higher flight speed makes it less sensitive and can be flown successfully even when there is not complete calm.

Note photo of completed model [main pic] is thanks to Simon Rogers.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Rhonsperber (oz15519) by Werner Thies, Willi Rolf 1975 - model pic

Datafile:

ScaleType:
  • DFS_Rhönsperber | help
    see Wikipedia | search Outerzone
    ------------
    Test link:
    search RCLibrary 3views (opens in new window)


    ScaleType: This (oz15519) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/DFS_Rhönsperber
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

There seems to be an error on the plan. The text states that the wings and fuselage are made from 3mm balsa but 4mm is shown on the plan.
pmw - 06/09/2024
I have the original book and can confirm the error in the text. The plan is drawn on a scale of 1:1 and the profile thickness is 4mm at the root. Therefore it is correct to use a 4mm thick balsa board.
Martin Huebner - 07/09/2024
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2024.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.