BAE Hawk (oz14917)
About this Plan
BAE Hawk. Control line profile scale model. Tractor prop layout. PAW 1.5 cc diesel shown.
Direct submission to Outerzone.
Update 10/11/2023: Added article, thanks to RFJ.
Quote: "BAE Hawk, by Bill Burkinshaw. Red Arrows Jet profile control-liner for 1.5cc engines.
IT HAS BEEN some years since I last designed and constructed a control-line model, not quite so many since I last flew one, so the challenge of producing a workable profile scale BAe Hawk quite got my adrenalin going.
After looking at a 3-view drawing of the BAe Hawk it was obvious that some slight modifications would have to be made in true semi-scale tradition. A slight increase to wing and tail areas and a mite off the nose length and the outlines began to look about right. Scaling up to a wingspan of 20in. would provide enough wing area for a 1-1.5 cc power model so the die was cast.
I resolved to start building the model straight away and leave details of bellcrank position, line guide and balance point until the model was roughly constructed. Once assembled and with a PAW 1.49 bolted to the front, a trial balance showed the balance point to be well in front of the leading edge. Not unexpected, but just confirmed! Looking under my work bench I found a box of lead weight and a little experiment showed 2oz or so to be sufficient to bring the balance point at least behind the leading edge.
With bellcrank fixed, it was tine to find the best position for the leadout guide. Easy enough, just hang the model up by two lengths of line from the bellcrank and slide a temporary line guide backwards and forward until the model was suspended straight up and down from bellcrank to suspension point.
Once finished, flight trials proved totally uneventful. Although the elevator is small and the balance point still a little forward of the desired point the little swept-wing jet flew away smoothly from the launch and ran the tank out without any fuss whatsoever. So, some six or more years since my last control-line flight and the model flew, and I could still fly it!
Construction: Mark out the wing outline noting the join lines for 4 in sheet shown on the plan followed by the other parts. Note that the 0.8mm ply fuselage doublers are fixed to the basic fuselage underneath the dummy jet intakes for their full length.
Cut the 3/8 square hardwood engine bearers to length and glue into position in the balsa fuselage profile followed by the ply doublers.
Taper the rear end of the dummy jet intakes down then sand to section before gluing in place. Carve and sand the wings to section then carve out the recess for bell-crank ply mount, wing tip weight and line guide before gluing into the fuselage slot. Slot the fuselage for the fin and tailplane, carve out the fuselage for the balance weight and fit all the remaining parts.
Bolt the bellcrank to the ply mount and glue this firmly to the prepared recess in the wing underside followed by the dummy wing fence line guide. Hinge the elevator to the tailplane using Terylene thread hinges and fit the control horn of your choice. Bend up and fit the pushrod.
Finishing: A coat of clear dope followed by one coat of sanding sealer and two coats of red dope overall, well sanded between coats provides the basis for the colour scheme. Mask the white stripe and paint this on. Draw the roundels with a ruling pen fitted to a pair of compasses, fill in with a small paint brush. The whole model should now be given a coat of clear fuel-proofer. Bolt on the engine and mount the tank with spring curtain rod and woodscrews, check the controls for freedom of movement and you are ready to fly.
Flying your 'Red Arrow': With a PAW 1.49 for power, 40 ft light 'Lay Strate' lines seemed just about right. A smooth level launch and she should be away. Control response is quite adequate, line tension is fine. The model will perform quite reasonable wing-overs and large loops. Once the engine has cut, full-up elevator produces a 1/4-lap glide.
This model is tough and easy to fly and looks great in the air, It should make quite a good trainer. It doesn't cost too much and is quick to build, what else can I say other than why not build one yourself? If you can persuade a couple of mates to build them too you should be able to put on a spectacular three-in-a-circle Red Arrows show!"
Supplementary file notes
Did we get something wrong with these details about this plan (especially the datafile)?
That happens sometimes. You can help us fix it.
Add a correction
BAE_Systems_Hawk | help
see Wikipedia | search Outerzone
search RCLibrary 3views (opens in new window)
ScaleType: This (oz14917) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.
If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.
ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/BAE_Systems_Hawk
Wikipedia page addresses may well change over time.
For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.
Do you have a photo you'd like to submit for this page? Then email email@example.com
User commentsThink this one was actually a free plan in Aeromodeller in the mid 80,s (when the mag increased size to A4) and the ad in the corner was something that appeared regularly at the time
Mike Hollamby - 10/11/2023
Aeromodeller Nov 1983, Balsa Cabin rekitted it later.
Pit - 10/11/2023
Aha, got it. Ok have set this now as from Aeromodeller. Many thanks.
SteveWMD - 10/11/2023
Add a comment
* Credit field
The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.
This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.
© Outerzone, 2011-2023.
All content is free to download for personal use.
For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.
Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.