ITOH 62-160 (oz14914)


ITOH 62-160 (oz14914) by Walt Mooney 1989 - plan thumbnail

About this Plan

ITOH 62-160 (aka ITOH N-62 Eaglet). . Peanut scale model for rubber power.

Quote: " ITOH 62-160, by Walt Mooney. This Peanut version of a 1960's Japanese lightplane is designed to break down for shipping to Postal Proxy Peanut contests.

Plans show how to make a shipping box from a single sheet of 1/4-inch balsa.

Postal Proxy Peanut contests, originally conceived by the editor/publisher of Model Builder, have caught on in several parts of the world. They present an easy way to have your models take part in international competition. Making a container strong enough to survive the mails intact, while carrying a completed Peanut, and paying the postage on that sort of package presents somewhat of a challenge. This is one response to the challenge: Make the model so it can be assembled for flight at the contest site, and fit in a relatively small box (shipping crate) that can be made strong and still light enough so the postal fees are not beyond your budget.

The shipping crate built for the ITOH 62-160 cost $2.16 for a sheet of 1/4 x 4 x 36 balsa and a dime or so for cement to assemble it. The 4 x 9-1/2 x 2-1/4-inch balsa box has adequate strength, will hold the model, documentation, three-views and photos, and the Post Office will charge less than $4.50 to send it from San Diego. California to Japan by airmail, with an enclosed letter.

The IT0H is a relatively simple, good flying design and uses standard building techniques throughout, with the exception of design details to enable it to be taken apart. This disassembly for transportation is commonplace with the larger models but has not often been done with Peanut Scale models.

Two materials are used to facilitate assembly. They will not be required if the model is not to be broken down for shipping. One thirty-second diameter, round bamboo is used for the wing spar carry-thru, strut leading edge, and rear spar pin. The bamboo is available from Peck-Polymers (see advertisement in this magazine). The other item is thin, one-sixteenth diameter plastic tubing to accept the carrythru, and strut ends. The material used in the model came from a plastic place mat. If plastic tubing is unavailable, make paper tube over .045 piano wire. Use tissue and model cement over an oiled length of wire.

The basic model structure does not require a lot of explanation if previous Peanut models have been built, so only things required for breakdown and assembly will be covered in this article.

The fuselage has several details which need coverage: The wing centersection is attached to the fuselage as a fixed item. The spar carry-thru tubing goes across the center section near the top, just behind the main spar. Note the location of this and the holes for the drag pins in the 'R-1' ribs. Be sure to make one extra 'R-1' to be cut down for the centerline rib in the wing center section.

There is a tail notch at the aft end of the fuselage to accept the horizontal tail. It does not go all the way to the leading edge of the tail, but it accepts the notch in the leading edge of the tail.

The rudder sockets in the fuselage are just holes in the balsa to accept the short lengths of pin that extend down from the front and rear of the vertical tail. The aft pin sticks down through the horizontal tail and keeps it in place. Strut tubes are located at each lower longeron just forward of the landing gear. Notice the crosspiece that leans forward like the strut. Two cross-pieces that lean aft accept the main landing gear. When installing them in the fuselage frame, put a piece of matchbook cover, or equivalent, between them to allow for the thickness of the gear wire.

The nose gear merely plugs into a balsa block built into the bottom center at the proper location. Where wires simply plug into holes in balsa, the holes can be hardened by the application of a little thin cyano adhesive. If done very carefully, the surrounding balsa is hardened without the holes being filled.

The wing panels have tubes to accept the carrythru,a bamboo drag pin and tubes to accept the upper end of the struts. Note that the tube hole in the 'R-2' rib is lower than in the 'R-1' to allow for the wing dihedral. The bamboo drag pin penetrates 'R-1' and extends to 'R-2' and is cemented to it at the 'X.' The drag pin should extend from the panel root about a quarter of an inch. Make a smooth point on the free end of the pin so it will penetrate the center section 'R-1' rib easily.

The struts are made with a round bamboo leading edge long enough to extend into the fuselage strut tube at the bottom, and the wing strut tube at the upper end. The balsa part completes the streamlined strut and is made to fit between the fuselage side and the wing panel bottom surface. The bamboo at the upper end of the strut may have to be bent to align with the wing tube. A little misalignment will not hurt because it tends to make friction between the bamboo and the tube and thus more secure struts.

The particular ITOH 62-160 modeled, JA3216, has a blue and white color scheme. The model was completely covered with white tissue which was water shrunk and given two coats of thin dope. The blue color was achieved by double covering with blue tissue,carefully cut to the pattern on the plan. Registration numbers are also blue tissue. Surface outlines were made with a fine, permanent felt pen. There is a black 'N' in the circular blue sky surrounding the swan on each side of the vertical tail.

Thin, clear acetate sheet (.003) was used for the windshield. The pattern shown is a good starting place, but all models vary a little, so first cut one out of paper for a trial fit. The side windows are simulated with black tissue. Pilot and passenger silhouettes are cut out of the black tissue, thus leaving white silhouettes when the tissue is doped over the white tissue. Pilot and passengers were then drawn in with colored felt pen, with just a touch of white correction fluid for the pilot's shirt collar.

Two nose block and propeller assemblies were made, one with a big propeller for flying and the other with a scale propeller for judging. This may not garner additional scale judging points, but the model looks better when it is sitting on the shelf.

The ITOH is a nice flying model. Ballast it as necessary, to get the balance point where shown on the plans. The tail notch can be widened at the aft end if up or down elevator is required. Both wings on the model pictured were warped to give about 3/32nd of trailing edge up (washout) at the tip and this appears to be about right. The model in the photos weighs 8.5 grams without rubber."

Direct submission to Outerzone.

Supplementary file notes



Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

ITOH 62-160 (oz14914) by Walt Mooney 1989 - model pic

  • (oz14914)
    ITOH 62-160
    by Walt Mooney
    from Model Builder
    October 1989 
    13in span
    Scale Rubber F/F Cabin
    clean :)
    all formers complete :)
    got article :)
  • Submitted: 02/10/2023
    Filesize: 293KB
    Format: • PDFbitmap
    Credit*: Pilgrim
    Downloads: 402

  • NotFound | help

    This is a scale plan, but ScaleType is set as NotFound.

    This happens when we can't find a relevant Wikipedia page to link to. Usually because the type in question is uncommon.

    Corrections? Use the correction form to tell us the new ScaleType link we should be using. Thanks.

ITOH 62-160 (oz14914) by Walt Mooney 1989 - pic 003.jpg
ITOH 62-160 (oz14914) by Walt Mooney 1989 - pic 004.jpg
ITOH 62-160 (oz14914) by Walt Mooney 1989 - pic 005.jpg

Do you have a photo you'd like to submit for this page? Then email

User comments

Here's a photo of my Walt Mooney ITOH 62-160 [main pic]. Outerzone plan 14914. It's a good flyer!
John Koptonak - 09/11/2023
Add a comment



Download File(s):


* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.


This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.


Terms of Use

© Outerzone, 2011-2024.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.