Piper Cub (oz13966)

 

Piper Cub (oz13966) by Herbert K Weiss 1938 - plan thumbnail

About this Plan

Piper Cub. Simple rubber scale model.

Direct submission to Outerzone.

Update 24/7/2022: Added article, thanks to Pit.

Quote: "Build the Piper Cub Minute Model. By Herbert K Weiss.

America's most popular airplane today, the Piper Aircraft Corporation's 'Cub', is the first ship to really break into the vast potential market of the air-minded public. The Cub is not yet a 'thousand dollar airplane,' but it is very near to it. With dual controls in an effectively furnished cabin the Cub seems to be giving its owners what they want, as is evidenced by the fact that over a third of all commercial airplanes sold today are Cubs.

Most significant in view of the large volume of Cub sales, is the fact that the Cub's top speed is only 84 miles an hour - fine for such a low powered ship, but nevertheless indicative of the intention of Cub owners to fly as they would drive their cars, safely and with economy.

Both aviation and the automotive industry owe much to the first wild spirits who burned the road and air in tricky experimental contraptions, but their number has always been small. A greater development from their beg,itmings requires the support of many enthusiasts. The Piper Corporation is leading the way in introducing to aviation a large and permanent group of supporters, to the eventual benefit of everyone concerned with aviation.

Our model this month has been designed for extreme simplicity. Because of the light construction, it flies very well.

Fuselage: With a sharp razor cut out two fuselage sides from 1/32 sheet balsa. The outline can be traced on the balsa by putting a sheet of carbon paper under the plan with the balsa under the carbon, then tracing the plan lightly with a sharp pencil. The rudder and stabilizer can also be traced and cut out of 1/32 sheet balsa at this time. Sand the pieces smooth on both sides with fine sandpaper.

Now cement the two fuselage sides together at the tail post, using a short piece of 1/16 square balsa as the tail post. Cut out former C from 1/16 sheet balsa, and A and B from 1/8 sheet balsa.

Cement the cross braces in place just at the rear of the windows, and follow these with the 1/8 x 1/16 braces at the landing gear. Add former C. Cement A and B together, and attach them to the nose of the fuselage as shown on the plan, using pins to hold them in place until the cement is dry.

Add the remaining cross braces, the tail hook and the landing gear. Note that the landing gear is all wire, covered with four sheets of tissue.

Wing: The wing is of standard construction. Make it in one piece, leaving the leading and trailing edge in rough form, and sanding them to airfoil section alter assembly. The bamboo wing. tip can either be bent over a candle flame, or as the bamboo bends freely. simply bent and tied into place with thin thread while the cement is drying.

Assembly: Sand the wing and fuselage again to remove any projections which would spoil the covering, then cover them carefully with tissue. Colored tissue may used in any color scheme to suit the individual builder. Spray the covered parts lightly and allow them to dry, Sand the 'fuzz' from leading and trailing edges and tack down loose edges of tissue with dope.

Now cement the wing to the fuselage, scraping the tissue from the frames at the joint so that the cement can hold the balsa. Add the tail surfaces, wing struts and wheels. The tissue-covered parts can now be given a coat of very thin dope if desired.

Carve the propeller from a block of medium hard balsa to the size shown.

Flying: The original model flew very nicely on two strands of 3/32 rubber, using about an inch of slack with a winder. A heavier model will need two strands of 1/8 rubber, and can probably take almost two inches of slack. The potentialities of these small models are surprising. Our Cub flies half a minute consistently indoors and rides the outdoor air very stably.

The usual adjustments are made in balancing. If the ship stalls add small hardwood wheels or dope the prop. If it dives warp the trailing edge of the stabilizer up. If the ship stalls under power do not apply down thrust, but instead note the direction in which it tends to circle. Then apply rudder in this direction and warp the trailing edge of the inside wing down to prevent spiral diving, if necessary. The model should then climb in a tight spiral under the initial burst of power."

Update 24/7/2022: Have rescaled this plan to 12 in wingspan. I am guessing this scan had been doubled in size (to 24 in) and that half of that at 12 inches is correct. Many thanks to vicnippert for spotting this.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Piper Cub (oz13966) by Herbert K Weiss 1938 - model pic

Datafile:
  • (oz13966)
    Piper Cub
    by Herbert K Weiss
    from Model Airplane News
    December 1938 
    12in span
    Scale Rubber F/F Cabin Civil
    clean :)
    all formers complete :)
    got article :)
  • Submitted: 13/07/2022
    Filesize: 274KB
    Format: • PDFbitmap
    Credit*: dfritzke

ScaleType:
  • Piper_J-3_Cub | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz13966) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Piper_J-3_Cub
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Piper Cub (oz13966) by Herbert K Weiss 1938 - pic 003.jpg
003.jpg
Piper Cub (oz13966) by Herbert K Weiss 1938 - pic 004.jpg
004.jpg
Piper Cub (oz13966) by Herbert K Weiss 1938 - pic 005.jpg
005.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

The Weiss Piper Cub plan is a lot closer to a Taylor J-2. I always wondered if perhaps he started drawing it just before Taylor and Piper had their falling out then just finished it with Piper J-3 rear windows. In any case it builds into a lovely model, I should get some pictures of mine for the site.
TimE - 25/07/2022
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2022.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.