Sopwith Baby (oz13857)

 

Sopwith Baby (oz13857) by David Boddington 1993 - plan thumbnail

About this Plan

Sopwith Baby. Radio control scale model biplane, for 20 to 30 size engines and 3 functions. Scale is 1/8.

Direct submission to Outerzone.

Update 31/5/2022: Added article, thanks to RFJ.

Quote: "I have to admit to being more than a little partial to the Sopwith designs. One of my all time favourites, both as a model and as a full-size aeroplane is the Sopwith Pup and I have modelled this prototype in many different sizes. Unfortunately, the Pup, unlike the Camel, was never fitted with floats and as waterplanes are another of my delights I had to find an alternative. It was but a short step, albeit a backward step in time to the Sopwith 'Baby'. Anyone familiar with Sopwith designs will immediately recognise the ancestry of the Baby, it is directly related to the 'Schneider'. winner of the 1914 prestigious seaplane race at Monaco and itself being virtually a 'Tabloid' on floats. However, the history of the 'Baby' is covered elsewhere in this issue.

The chisel-nosed version of the Baby was chosen simply because the shape makes an attractive change from the radial cowled version (subject of Brian Downham's 63 in wingspan version RM174). Choosing the Baby in preference to the Schneider was for more practical purposes, the former aeroplane has a larger fin and rudder area, the Tabloid and Schneider designs being somewhat marginal in this respect.

From the outset the Baby was designed to be operated from water, even though it is a relatively small model, and for that reason waterproofing should be considered throughout the construction and finishing. It can, of course, be operated from the land using a small scale-like beaching dolly and landing back on the floats. Over to Shaun Clay.

When I originally wrote these instructions it was with the intention of building the model myself. As usual, time looked like being the victor but then Shaun Clay offered (who said coerced!) to build the model. Readers may remember that Shaun also built the Heinkel He46 pull-out plan model featured in the April/May '92 issue of RCSA. I knew, therefore, that the model would be beautifully made and would have the best chance of success during the test flights.

Shaun has one or two ideas on construction of scale models and one of his pet ideas is being able to remove all struts from the fuselage and wings to allow for easy covering. Comments on these modifications, also obvious from the accompanying photographs, are included at the end of the main article. You have the choice of following the original drawings or making the modifications carried out by Shaun.

Before the Off: Study the drawings and read the construction notes until you fully understand all parts of construction, it is a conventional form of structure. The upper and lower wings are in one piece and do not rely on additional strength from the rigging wires, these can be elasticated dummies. Outlines are as accurate as the existing drawings available permit and wing chord, span and lengths, etc, are taken from established data. Wing section does not include undercamber, if this is to be incorporated I would suggest that plug-in wings and working rigging are also used. (See the 1/4 scale version).

Mark onto the drawings the precise location of the radio equipment, engine and fuel tank. Positions of prototype model installations are shown on the drawings and, as normal with WWI short nosed byplanes, keep the equipment as far forward as possible. Engine bearer widths should be adjusted to the particular engine used. or you can revise them to feature bearers and an engine plate.

Keep thinking about eventual waterproofing throughout the construction, ie no holes from outside to inside unless absolutely essential. Where you have control cables or rods exiting the fuselage the supporting tubing should give a minimum clearance and petroleum jelly applied to the exit point to minimise the risk of water ingress. Build in a narrow bore plastic tube for routing the aerial and to exit the rear fuselage adjacent to the rudder.

Make up your kit of parts, accuracy is important, and we are ready to start gluing - with a water resistant adhesive!

Fuselage: Construct two fuselage side frames from 3/16 sheet and 3/16 sq strip for the open structure at the rear. Note that the top front edge of the sheet is chamfered to follow the cross section, there are cut-outs for the centre section struts and the 1/8 sq diagonal members are set back from the surface (you could cross brace with strong thread for a real scale-effect).

Face the outside front area with microply (0.4mm plywood) if you have real difficulties in obtaining this material thin plastic sheet (plasticard) could be used as an alternative. Remember however that it would not be possible to use cellulose finishes with most of the plastic sheet materials.

Glue servo bearers and the wing fixing plate (predrilled) and crosspieces to the formers and then glue formers F3 to F9 in the marked positions on the fuselage sides. Check for squareness and leave to dry.

The top cowling is formed with laminations of 1 in block and a centre 3/16 piece. Glue them in place ready for final carving after the engine bearers and F2/F1 have been fitted, Fit the fuel tank at this time and the elevator horn assembly.

Make up the centre section struts (use a simple jig when soldering the cross bracing) and sand the struts to an oval section above the fuselage side location. Epoxy the centre section frame in position. followed by the .4mm plywood top decking. With the front of the fuselage now rigid the rear of the fuselage can now be brought together by gluing the crosspieces and rear formers into position. Check at all stages that both sides have an equal curvature. Add the top decking formers and stringers..."

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Sopwith Baby (oz13857) by David Boddington 1993 - model pic

Datafile:

ScaleType:
  • Sopwith_Baby | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz13857) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Sopwith_Baby
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Sopwith Baby (oz13857) by David Boddington 1993 - pic 003.jpg
003.jpg
Sopwith Baby (oz13857) by David Boddington 1993 - pic 004.jpg
004.jpg
Sopwith Baby (oz13857) by David Boddington 1993 - pic 005.jpg
005.jpg
Sopwith Baby (oz13857) by David Boddington 1993 - pic 006.jpg
006.jpg
Sopwith Baby (oz13857) by David Boddington 1993 - pic 007.jpg
007.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

See video at: https://www.youtube.com/watch?v=7aLofZQ5Lt4
Pit - 31/05/2022
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2022.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.