EFA (oz13853)


EFA (oz13853) by Sandy Riddell 1994 - plan thumbnail

About this Plan

EFA. Radio control scale model jet fighter. All-sheet design for .15 engine, with tractor prop layout.

Quote: "EFA. An all-sheet model of Europe's 21st Century fighter for .15 engines and three-channel R/C, designed by Sandy Riddell.

The European Fighter Aircraft or EFA is not to be confused with Eurofighter which is actually the name of the manufacturing consortium that has been set up to build it.

The EFA design can be traced back to the beginning of the eighties when Europe's air forces saw the need to replace their older generation of attack aircraft. The new generation of (then) Soviet fighters was seen to be the major threat that had to be countered. Thus whatever was chosen to re-equip Europe's air forces had to be capable of bettering the Mikoyan and Guryevich (MiG) 29 designated by NATO as the 'Fulcrum' and the extremely agile Sukhoi 27 designated 'Flanker'. This goal required the best that modern Western technology could deliver in engine design, lightweight composite construction, fly-by-wire and complex avionics.

The result of over a decade of design, testing, construction and not a little political wrangling is the EFA. It doesn't even have a real name yet, the ideal one (Eurofighter) was wasted on the company that's building it! The first two prototypes were rolled out in early 1993 and the RAF will be using their EFAs to re-equip the current Jaguar and the older Tornado squadrons.

Why I built it: One of the members of my local club (Linlithgow Radio Flying Club) recently bought a German kit of a MiG 29. It was a relatively small chuckle with a .19 motor up front. I was so impressed with it that I wanted to build something similar. As a suitable subject, the EFA almost chose itself as it's been in the news so much and, anyway, what better adversary could there be for the MiG than the plane that was designed to beat it?

I initially set myself two limitations, these were: Firstly the model must be quick to build. The second limitation I set myself was that it should be inexpensive to build. This was due in part my natural Scottish temperament but also to limit the (financial) damage if it was a total flop! This being only my fourth design, the latter possibility seemed not altogether unlikely.

Working from a three view drawing published in the 1988 Farnborough freebie, I scaled up the dimensions to give a model size with a wing loading of about 1 lb per square foot. The canards are out of scale, they just looked too small and I reduced the size of the air intakes by about fifty percent. Other than that the model is pretty accurate.

If, like me, you always read the bit at the end about how it flies first and then go back to the rest of the article, you will already know that my fears about the design were totally unfounded. I succeeded in designing and building the model in just three weeks, which for me is nothing sort of miraculous. As the model is relatively small (just wait and see how quickly it can get out of sight), the cost/amount of balsa needed is also quite low. I succeeded in completing the project on time and on budget, that's one up the real EFA!

How to do it: An OS 15 provides adequate power on my model and the flying surfaces are all 1/4 in sheet light balsa. I tried to build as light as possible through careful wood selection and covering. I used cyano for everything except fixing the canopy for which I used five minute epoxy.

The model is a standard box construction with all sheet flying surfaces - anyone with experience of building from a plan should have no difficulty: If you haven't got the experience to build it without detailed instructions, then the chances are you haven't got the experience to fly it (so be warned). I will say a little about some of the construction and the more unusual features though.

I started construction with the wings, 1/4 in lightweight sheet balsa butt-jointed together. The wing, leading edge root extension, trailing edge, anti-twist tips and elevon torque rods are all laid up in one flat section. The fuselage is built, and added to the wing in two sections.

The lower fuselage section and the air intakes are made from I/8in balsa with a ply section tin wide at the front - bottom edge of the intake. This ply piece will bear the brunt of any fast landings. The upper fuselage is a box with 1/8in balsa sides (with 1/32 ply doubler at the front), and 1/4 in top and bottom sheets, 3/8 triangular section at the joint allows the necessary degree of rounding to be achieved. Unless you decide to build in a hatch (I didn't, because I thought the model wouldn't last long enough to need it), the battery needs to be installed before the rear sheeting is complete.

The hatch is quite neat, it uses the canopy join as the front locator and a tongue-and-groove arrangement around the fin at the rear. The canopy is cut into two sections and the front section is epoxied to the fuselage and framed with 1/2 in wide strips of 1/32 mirror ply. The band of ply which goes round the join acts as the front locator for the rear section of the canopy which is glued to the hatch..."

Direct submission to Outerzone.

Supplementary file notes



Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

EFA (oz13853) by Sandy Riddell 1994 - model pic

  • (oz13853)
    by Sandy Riddell
    from Radio Modeller
    September 1994 
    24in span
    Scale IC R/C LowWing Military Fighter
    clean :)
    all formers complete :)
    got article :)
  • Submitted: 19/04/2022
    Filesize: 727KB
    Format: • PDFbitmap
    Credit*: KevinBranch

  • Eurofighter_Typhoon | help
    see Wikipedia | search Outerzone

    ScaleType: This (oz13853) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.

    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Eurofighter_Typhoon
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

EFA (oz13853) by Sandy Riddell 1994 - pic 003.jpg
EFA (oz13853) by Sandy Riddell 1994 - pic 004.jpg
EFA (oz13853) by Sandy Riddell 1994 - pic 005.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment



Download File(s):


* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.


This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.


Terms of Use

© Outerzone, 2011-2022.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.