Miss Simplicity (oz13456)

 

Miss Simplicity (oz13456) by Henry Gordon from Flying Models  1948 - plan thumbnail

About this Plan

Miss Simplicity. Simple all-sheet rubber sport model.

Quote: "For fun galore with little work, nothing beats a good all-balsa ROG. Miss Simplicity, by Henry Gordon.

Most modelers consider the basic ROG kid stuff. But, if every old timer were to tell the truth, they would admit to many happy, pleasurable hours derived from this type of plane.

Only a fundamental understanding of sheet balsa and the adjustment of models is required to build and fly this particular plane. Sheet balsa of uniform texture is needed, so select your wood with this in mind. Avoid wing wood with hard or soft spots through the grain. The correct wood will assure clean undercamber throughout the wing length and prevent tlat or bowed sections after the wing is shaped upon the wing former.

To facilitate the shaping of the wing, apply light, clear dope to the undersection of the wing. To shape the wing, hold it to its proper form while the dope is drying. To prevent warpage, don't apply dope to the stabilizer or rudder.

At the very least, three coats of dope should be put on the Fuselage. This will both protect it and keep it clean. The wire parts are easily shaped with a pair of round nosed pliers. Note the form of the propeller hook. Bend it very carefully so that the free-wheeling unit will work smoothly.

The assembly of this hook to the prop is done next. Bend the nose, or free-wheeling lock, first. Now slip a small, light washer (made from .005 brass shim stock) over the shaft and solder to the flat section at the lock. This washer will prevent the tension spring from riding over the lock.

The small tension spring may be obtained from your Model Dealer or it can be made from .010 or .012 control-line wire by winding it at home yourself. Slip the spring in place and insert the prop shaft. Remember at this point to place another small washer between the spring and the hub. After putting the hook into the prop, you can then bend the motor hook end and the prop shaft is finished.

Propeller carving shouldn't prove difficult at all. Use a very sharp pen knife to whittle out the approximate form and finish shaping with sandpaper. Mark the prop outlines to the dimensions shown on the plan. Start your carving on the lower surfaces first. Take long slicing strokes for the outline. Diagonal strokes are necessary for correct shaping of the undercamber in the prop..."

Direct submission to Outerzone.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Miss Simplicity (oz13456) by Henry Gordon from Flying Models  1948 - model pic

Datafile:
  • (oz13456)
    Miss Simplicity
    by Henry Gordon
    from Flying Models
    June 1948 
    15in span
    Rubber F/F
    clean :)
    all formers complete :)
    got article :)
  • Submitted: 16/11/2021
    Filesize: 111KB
    Format: • PDFbitmap
    Credit*: theshadow

Miss Simplicity (oz13456) by Henry Gordon from Flying Models  1948 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2021.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.