About this Plan
EXP-1R. Radio control sport model with twin boom pusher layout. For electric power with 540 can motor.
Quote: "Try this shapely pusher for 540 electric motors. EXP-1R, by Chris Martindale.
I have been flying electric powered models for almost two years now, and I have been striving to produce some unusual but attractive electric aircraft. Readers will have probably seen my previous design Electro Jet (oz11303) in another modelling magazine, which has proved that electric flight is not all large area, lightweight and flimsy aircraft but can be compact, attractive, manoeuvrable and lots of fun.
I decided to continue my efforts in producing attractive, unusual models and this, my latest creation, has seemed to spark off quite a lot of interest both in my club at Widness and a couple of others in the North West area. This model with its twin booms, high mounted tail and pusher engine configuration does look very different in the air to say the least.
What's in a name? The name 'EXP 1R' was arrived at mainly due to my hopelessness at making up names and also making templates for letters!
The original was named EXP 1, but unfortunately it met its demise on its first outing, due to radio problems. After analysis of the disaster I discovered to my horror that I had been flying with no aerial on my receiver yet was able to achieve some 80 metres range which, for my Century Systems club receiver, is exceptional (excellent bit of kit, I would recommend this equipment to anyone - provided it has the correct antenna for proper reception). Anyway, I digress; the original model flew so impressively while it was in the air I just had to build another to replace it, hence the birth of EXP 1R.
Many people have asked me why I use a flat-bottomed wing section on my electric models. The answer is simple; (i) for ease of construction, ie the wing can be built flat on a board and requires no jigging, and (ii) flight performance - for a given speed a flat-bottomed airfoil section will generate more lift than a symmetrical airfoil, so, at the end of a run when power is at an absolute minimum, landings can be stretched that much further using a flat bottomed wing without the model falling out of the sky. Now, let us cut some precious balsa.
Wing: I always seem to opt for constructing the wing first when I am building a model. Commence by forming the two wingskins by butt jointing two 100mm wide by 1.5 mm thick sheets of balsa for each skin. The top skin will require a further 25 mm wide strip glueing on to allow for the curvature in the wing section. Set the skins aside to dry and, in the meantime, cut out all the ribs and make them all the same size.
Once the wingskins are dry, sand them smooth and lay the bottom skin on a flat building board and transfer all the planform and rib spacing measurements from the plan to the bottom skin. Glue on the 6mm square false leading and trailing edge strips and trim up all the ribs to the correct length, cutting them off at the trailing edge.
The correct taper in thickness of the wing can be achieved by skewing the template on a full-size rib and trimming to shape. Glue in all ribs, 3 mm horizontal grain spar and the extra supports for the booms (note that the starboard side is different to accommodate pushrod exit). Glue in the 6 x 3 mm balsa supports and the 1.5 mm ply bellcrank plate, fabricate belicrank and pushrod assembly and install into the wing. A good tip here to keep the bellcrank at neutral is to make the pushrod from the bellcrank to the centre of the wing the correct length so that when it hits the centre rib the crank is at neutral.
Plane the leading and trailing edge strips to profile of wing section and glue on the top wingskin. Use plenty of pins to hold every joint down both to the ribs and the leading and trailing edges. You will find that the top skin will require trimming along the leading edge to facilitate the adequate securing of the sheet at this point. Once this assembly has dried overnight it can be lifted from the board, all waste ends and edged trimmed up and the leading edge capping fixed in place. Add tips, tip gussets and filling pieces and sand to shape when dry.
All that remains now is to make up the ailerons from 32 x 6 mm trailing edge section and glue on the aileron cranks. The bearings for the cranks are formed by grooving a piece of TE section and fill with epoxy, grease the cranks with Vaseline and put this assembly in place on the wing. Once the epoxy has set the cranks should remain free..."
Supplementary file notes
Did we get something wrong with these details about this plan (especially the datafile)?
That happens sometimes. You can help us fix it.
Add a correction
Do you have a photo you'd like to submit for this page? Then email email@example.com
User commentsNo comments yet for this plan. Got something to say about this one?
Add a comment
* Credit field
The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.
This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.
© Outerzone, 2011-2021.
All content is free to download for personal use.
For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.
Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.