Minislot (oz13287)

 

Minislot (oz13287) by Roy Clough from Model Builder 1993 - plan thumbnail

About this Plan

Minislot. Free flight sport model for electric power.

Note Zoomslot and Minislot both appeared in the same article in MB, Oct 1993.

Note for the original 'Build a Flying Saucer' free flight design from the first time around, see Flying Saucer (oz9528) from Air Trails, Aug 1952.

Quote: "Not one but two great flying modern versions of the author's famous 'slot saucer' of the 1950s.

Minislot Saucer. For small field FF fun, try this ultra-simple electric slot saucer. Uses an inexpensive HiLine power system.

Powered by a HiLine Mini-6 motor, this 38-year-old design will draw interested attention at any flying site.

The slot saucer is perhaps one of my most famous designs, but no mention of it would be complete without acknowledging the fact that, although I invented it, Fran McElwee secured its place in history. Since the 60s, his larger radio controlled versions have been stealing the show wherever they have been flown.

Minislot is built from a sheet of light-weight polystrene bubble foam and 1/32 and 1/16 balsa glued together with thick UFO CA glue, which works great and won't melt foam.

There is no pretense of an airfoil section, and except for a purely optional rudder tab, no control surfaces. Balance and flight trim is achieved by moving the batteries as needed.

The Minislot Saucer must be slightly dished to secure recovery coupling. Trim a curve into the last third of the central stiffening spine to raise the trailing edge of the saucer 1/4 inch.

The underbelly fin exists solely to protect the prop and motor. You can leave it off or install the two-wheel landing gear devised by test pilot Skip Ruff for flying over the gravel that passes for model flying sites in California.

The motor is mounted with two 1/16 x 1/4 balsa legs which, with the Mini-6's fiberglass shaft carrier, are stuck to the 1/32 balsa base with one small drop of CA each. In the event of a crunch, the wood will split off without damage to the motor. The above-center thrustline needs 1 to 1-1/2 degrees upthrust.

The three-cell 110-mAH battery pack that came with the Mini-6 works great, but I fly from a small field and wanted less duration and more pizazz. Dick Henderson had sent me four tiny 50-mAH cells; I used them with good results in a simple battery holder. NiCd manufacturers advise against soldering cells because excessive heat can ruin them. While most of us seem to get away with soldering larger cells, a holder makes more sense for the very small cells as they have little capacity to dissipate heat. (Commercial packs are assembled with a spot welding technique that imposes virtually no heat on the cells' interior.)

Stick a small piece of double-sided tape to the battery pack or tube and use it to shift the pack fore and aft and sideways until the saucer glides with about a 5:1 mush and a barely perceptible left turn. The ideal adjustment is climbing left-hand circles a hundred feet or so in diameter. When you are satisfied you have the balance point nailed down, replace the tape with a couple drops of CA.

Wiring hookup is total simplicity. Hooks bent into the tinned positive leads serve as a switch. Recharge is via a couple of color-coded alligator clips from a pocket battery pack. I use a charging pack with one more cell than the flight pack and leave the clips on until the pack being charged is just perceptibly warm. Bench charging at .5 amp for 3-5 minutes will pack in a bit more duration. "

Direct submission to Outerzone.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Minislot (oz13287) by Roy Clough from Model Builder 1993 - model pic

Datafile:
  • (oz13287)
    Minislot
    by Roy Clough
    from Model Builder
    October 1993 
    12in span
    Electric F/F
    all formers complete :)
    got article :)
  • Submitted: 25/08/2021
    Filesize: 276KB
    Format: • PDFbitmap
    Credit*: MB2020

Minislot (oz13287) by Roy Clough from Model Builder 1993 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2021.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.