B-17 Flying Fortress (oz13181)

 

B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - plan thumbnail

About this Plan

B-17 Flying Fortress. Radio control scale model WWII bomber, for 4x 3.5cc two-stroke engines.

Direct submission to Outerzone.

Update 20/07/2021: Added article thanks to RFJ.

Quote: "Evocative rendition of this four-engine American bomber spans 76 in and can be flown on four to six-plus function radio and four engines up to 3.5cc in size. B-17 Flying Fortress, by Pavel Bosak.

I have wanted to build a multi-engined airplane ever since I took a piece of plywood and spruce in my hand for the first time. There was something very romantic about this type of aircraft's slightly out-of-synch drone as it made a high pass that I could not ignore. Of course, as with most dreams, I had to wait a few years before I could turn it into reality and first I built two twin engined models - the Cleopatra and the Water Ranger which was a seaplane.

The first four engined model that I built was also a seaplane - the Boeing B-314 Yankee Clipper and the latest one is this B-17 Flying Fortress. I will not say anything about the history of this famous aircraft here since it has been so well documented many times before, so in this article I will tell you only about the model.

This model cannot be described as true scale - only semi-scale. Although the dimensions are correct , I have not added a great deal of detail to the model in order to make it simpler than true scale. There is no reason however why more detail should not be added. As you can see from the photos, the model does look very realistic even from a very short distance away.

Wings: When you start to build this model, you have to start with the wings since you will need the wings completed before you make a start on the fuselage.

The wing is of all balsa construction and the ribs for each panel are made up using the sandwich method. Cut balsa rectangles slightly larger than the size of the biggest rib. Make plywood templates of the root and tip ribs W1 and W12 according to the plan and sandwich the required number of rib blanks between them. By sanding the blanks smoothly between the two plywood templates, you will make all the ribs at the same time. It is useful to mark the ribs with the corresponding numbers over the plan. Cut all the slots and notches as required. Ribs W1,2,3,5 and 6 are strengthened with 1mm plywood. The wings are now built directly onto the main and subsidiary spars. Glue the false leading edge W15 from 5mm balsa in position. Both wing halves are then glued together with plywood braces W22 and W23. Now sheet the bottom of the wings and install the aileron and throttle pushrods and linkages.

Between ribs W2 and 3 and W5 and 6, glue hardwood rails for the engine mountings. Between ribs W5 and 6 also fit the hardwood rails for the undercarriage mountings. Glue W21 and the hardwood wing dowels in the front of the centre section of the wings and cover the rest of the top of the wings.

Glue the trailing edge W16 from 10mm balsa and the wing tips in position. Cut bulkheads N1 and N2 and glue them in position at the engine mounting beams. Install the fuel tanks into the wings and, from 5mm balsa, plank the nacelles. Sand the whole wing and cut out the ailerons and flaps. Onto the wings, glue W17 and WI9. At the flap positions glue part W18 and at the aileron positions glue part W20. These are all from 10mm balsa. Flaps and ailerons are connected to the wings with nylon hinges.

Stabiliser: The stabiliser is of very simple construction. Make the basic balsa frame according to the plan from 5mm balsa covered on both sides with 3mm balsa. Sand the leading edges to section. The elevators are sanded from 10mm balsa sheet and fitted into place with nylon hinges. The elevator halves are connected with 3mm piano wire.

Fuselage: The building process for the fuselage is a little complicated to start with because the model does not have 'classic' fuselage sides. Cut out all the fuselage formers F1-F9 from the materials shown on the plan. To start building the fuselage you will have to use a fuselage jig. Fix the fuselage formers in their correct positions in the fuselage jig and, from 10mm wide balsa, start planking the fuselage, starting at the bottom and moving alternately outwards. Once the fuselage has some rigidity to it, you can remove it from the jig to complete it if you wish, although more accuracy is ensured if you use the jig throughout.

Once the fuselage has been completely planked, cut away the areas around the wing position. Fit the captive nuts for the wing fixing bolts in position and trial fit the wing. Sand the fuselage as required until the wings are a perfect fit and then sand the rest of the fuselage.

Glue the cockpit floor in position and install the crew. In my model, I used small puppets as crew-members with the pilots' seats and the instrument panel made from scrap balsa. Now glue in position the acetate canopy windows and, from block balsa, make a canopy roof. The same method is used for the rear gunner's position. The front, dorsal and belly turrets are moulded from thin sheets of acetate.

The frame of the fin is made from 10mm balsa. The shape is shown on the plan. Glue the former F10 in place and cover the fin with 3mm balsa sheet both sides. The rudder is made from 3mm balsa with 14mm balsa where the hinges will fit in position. The rudder is fixed at Fl with nylon hinges. After the fuselage has been sanded, cut out the hole for the elevator and epoxy it in place.

Covering and painting the model: The choice of finishing methods is best left to the builder since each of us has our own favourite method. My B-17 was finished with thin Modelspan tissue and six coats of clear dope were used. The colour scheme was done with acetone based paint. The panel lines and hatches were applied with a technical pen and black ink. After the insignia and labelling were painted on the entire aircraft was given a final coat of fuel proof clear lacquer.

Finishing of the model: Install everything into the model. I used Rom-Air landing gear although only for the main gear - the tailwheel is fixed in the down position. The tank and operating valve is in the fuselage.

Install the engines - I used four 3.5cc engines although I am sure that you could safely use smaller units because my B-17, flying with full throttle, is more like an aerobatic model! Install the radio gear and make sure that all functions are working correctly.

Check the centre of gravity carefully, making sure that it balances where shown on the plan. In my model, I had to install 20dcg (around 7oz) of lead in the nose to make it balance.

Flying the model: The flying characteristics of the B-17 is the same as any other model as long as all the engines are working properly. If one engine stops, you can still continue the flight but if two engines stop on the same side, you must throttle back the remaining engines immediately and land. It is not a clever thing to continue a flight in this configuration!

I have fitted flaps on the B-17 and, although not strictly necessary, I use them for take off and landing which gives the model a very short take off and landing roll. In the air, the B-17 is very realistic although not quite so realistic at full throttle! From straight and level at full throttle I can fly rolls, loops and inverted flight with no problems whatsoever!"

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - model pic

Datafile:
  • (oz13181)
    B-17 Flying Fortress
    by Pavel Bosak
    from RC Model World
    March 1994 
    76in span
    Scale IC R/C LowWing Multi Military Bomber
    all formers complete :)
    got article :)
  • Submitted: 05/07/2021
    Filesize: 780KB
    Format: • PDFbitmap
    Credit*: theshadow

ScaleType:
  • Boeing_B-17_Flying_Fortress | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz13181) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Boeing_B-17_Flying_Fortress
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - pic 003.jpg
003.jpg
B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - pic 004.jpg
004.jpg
B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - pic 005.jpg
005.jpg
B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - pic 006.jpg
006.jpg
B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - pic 007.jpg
007.jpg
B-17 Flying Fortress (oz13181) by Pavel Bosak from RC Model World 1994 - pic 008.jpg
008.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • B-17 Flying Fortress (oz13181)
  • Plan File Filesize: 780KB Filename: B-17_Flying_Fortress_oz13181.pdf
  • Supplement Filesize: 2964KB Filename: B-17_Flying_Fortress_oz13181_article.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2021.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.