Taylorcraft (oz13082)

 

Taylorcraft (oz13082) by Gerald Skrjanc from Micro-X 1980 - plan thumbnail

About this Plan

Taylorcraft. Rubber scale model.

Quote: "Instructions: The T-Craft has been designed as an easily-built lite model that can be flown indoors or outdoors. If you build carefully and follow these instructions, you will have an excellent flying model.

For cutting wood to shape, use a sharp, pointed blade, such as an X-acto #11. Do not pin through wood strips, but around them. You may have to wet the 1/16 strips where sharp curves are necessary. Use stronger strips for longerons on body and lite ones for cross members, uprights on body and all parts of stab and rudder.

Cut wing ribs and use 3/32 sq on edge for leading edge and the 1/16 x 1/8 for trailing edge. Wing is built flat on plans. Tiny gussets in wing and at body bottom, marked with a (+), are glue stations for wing struts, which are 1/16 x 1/8 sanded to streamline section. These are omitted on plan for clarity.

Build two body sides on plans leaving off F-1 and F-2, until sides are glued together using top view for cross-piece length. Then add F-1, F-2, and cowling on top front. Fit nose block in place and sand to shape, but do not glue. Slip landing gear assembly and tail wheel in bottom. Put several coats of dope on body, wing, stab and rubber framework, when they are completed, and sand carefully; then apply paper. Working with each part individually, shrink paper with fine water mist, paying careful attention to prevent warping. If warping does occur, straighten before applying one or two coats of thinned clear dope.

Although any 6 in diameter prop may be used, we've had good results with the following one. The prop is in three pieces: two removable blades and a hub. The hub consists of a piece of 3/16 sq balsa 1-1/2 in long, and has slotted ends, edge to edge at right angles. Slots are 3/8 deep. Prop shaft hole goes through the center on flat side of wood. Sand this unit round and wrap with thread at end of slot to prevent splitting. Prop blades are sanded streamline, then wet and wrapped around a 3 to 4 in diameter bottle (large pop bottle OK) at a slight angle, wrapped with newspaper, and baked in oven at low temperature until dry. The angle on which blade is placed on bottle determines prop pitch - more angle, less pitch. Blades are not glued in hub and several sets of blades can be made at different angles to suit flying site.

Fly model in right circle by gluing nose button on angle to achieve right thrust and down thrust. Add more down thrust to correct tendency to stall at beginning of flight. Nose block should be removable for winding, and final thrust setting can be made by gluing shims to back of removable noseblock. If model spiral dives in right turn, twist leading edge of right wing up (wash-in)."

Direct submission to Outerzone.

Supplementary file notes

CO2 conversion.
Printwood.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

No model pic found for this plan

Datafile:
  • (oz13082)
    Taylorcraft
    by Gerald Skrjanc
    from Micro-X
    1980 
    22in span
    Scale Rubber F/F Cabin Civil Kit
    all formers complete :)
  • Submitted: 24/05/2021
    Filesize: 388KB
    Format: • PDFbitmap
    Credit*: AdrianCulf

ScaleType:
  • Taylorcraft_B | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz13082) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Taylorcraft_B
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Taylorcraft (oz13082) by Gerald Skrjanc from Micro-X 1980 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • Taylorcraft (oz13082)
  • Plan File Filesize: 388KB Filename: Taylorcraft_oz13082.pdf
  • Supplement Filesize: 1241KB Filename: Taylorcraft_oz13082_co2_conversion.pdf
  • Supplement Filesize: 1935KB Filename: Taylorcraft_oz13082_printwood.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2021.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.