Fokker Eindecker (oz12887)

 

Fokker Eindecker (oz12887) by Mike Leasure from Davey Systems 1990 - plan thumbnail

About this Plan

Fokker Eindecker. Radio control scale model for .049 engine (or electric) and 2 channels. Wingspan 36 in, wing area 240 sq in.

Note the plan shows wing at both 36 inch span for .049 power, and at 40 in span for electric power.

Quote: "Davey Systems Corporation. DSC Eindecker Building Instructions.
The stand-way-off scale EINDECKER that you are about to build is a convertible kit, permitting use of a 1/2A engine or a 05/075 electric motor, such as the DSC 075 HYPERTHRUST motor that is supplied with the special version of this kit. You also have a choice of a 36 or a 40 inch wing. We recommend the 40 in version, particularly if you are building the heavier electric motor option.

In building the kit, we suggest you use the new cyanocrylate adhesives, both the thin and the gap filling types with an accelerator when required. Prior to starting, look over the plans and kit contents carefully to became familiar with the kit and the construction. The choice of motor or engine option is explained as you progress. You can always change to the engine from the motor by covering the motor hole with a small piece of plywood.

The EINDECKER is built from die and machine cut balsa and plywood. It is not a complex kit. Parts are bagged for your convenience and are easily identified. If you follow the instructions and don't rush, you will have a durable, great flying model that you will be proud of.

WING: The wing is constructed in the normal manner. Keep in mind that the pre-cut parts as supplied are accurate. If there appears to be a fit problem, it will be because the plan has stretched during the blueprinting process. Before you start, cover the plans with waxed paper or a clear plastic sheet, such as the leftover carrier sheet from your last covering job. The wing is built in three pieces and put together with the 1/32 plywood brace and the 3/32 balsa gussets. whether you build the 36 or the 40 in version the method is the same.

1. Position the bottom spar over the plans and pin in place. Cut the spar in two places under the two 1/16 W-2 ribs.
2. Position and glue all of the W-1 ribs in place. Cut 1/16 in off of the top and bottom of two W-1 ribs for the center section as shown which is planked with 1/16 balsa sheet.
3. Position and glue in place the leading and trailing edges. Position and glue the 3/16 square wing tips.
4. Cut the three W-2 ribs in half at the rear edge of the spars. Cut, fit and glue the bottom center sheeting between the leading edge and the spar and the spar and the 1/4 x 3/8 rear. Two of the W-2 ribs are made by trimming off 1/16 in from a W-1 rib... "

Direct submission to Outerzone.

Update 24/03/2021: Added review from Radio Modeller, March 1993, thanks to GerritL.

Supplementary file notes

Instructions.
Review.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Fokker Eindecker (oz12887) by Mike Leasure from Davey Systems 1990 - model pic

Datafile:
  • (oz12887)
    Fokker Eindecker
    by Mike Leasure
    from Davey Systems
    1990 
    36in span
    Scale IC Electric R/C Military Fighter Kit
    formers unchecked
  • Submitted: 03/03/2021
    Filesize: 576KB
    Format: • PDFbitmap
    Credit*: DuaneHolliger

ScaleType:
  • Fokker_E.I | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz12887) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Fokker_E.I
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Fokker Eindecker (oz12887) by Mike Leasure from Davey Systems 1990 - pic 003.jpg
003.jpg
Fokker Eindecker (oz12887) by Mike Leasure from Davey Systems 1990 - pic 004.jpg
004.jpg
Fokker Eindecker (oz12887) by Mike Leasure from Davey Systems 1990 - pic 005.jpg
005.jpg
Fokker Eindecker (oz12887) by Mike Leasure from Davey Systems 1990 - pic 006.jpg
006.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • Fokker Eindecker (oz12887)
  • Plan File Filesize: 576KB Filename: Fokker_Eindecker_oz12887.pdf
  • Supplement Filesize: 2429KB Filename: Fokker_Eindecker_oz12887_instructions.pdf
  • Supplement Filesize: 1161KB Filename: Fokker_Eindecker_oz12887_review.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2021.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.