Robin HR100 Tiara (oz12721)

 

Robin HR100 Tiara (oz12721) by Walt Mooney from Model Builder 1975 - plan thumbnail

About this Plan

Robin HR100 Tiara. Rubber scale model.

Quote: "Our Premier Peanut Potentate selected another French design for this month's model. Taking advantage of the optional hand launch, the Robin has put in 40 second indoor flights.

When I finally received my copy of 'The Observers Book of Aircraft,' by William Green and Dennis Punnett, 1974 edition, I immediately thumbed through it to see if there were any three-views that would make up into a nice Peanut Scale model. The French Concern, Pierre Robin, has just brought out a new model called the HR.100 Tiara. The Tiara name comes from the fact that this aircraft is powered by a 320 hp Continental Tiara engine. The three-view showed that the Tiara would make up into a very nice Peanut. It has plenty of dihedral, a fairly low aspect ratio wing, and a good sized vertical tail. The horizontal tail might be large enough, but I enlarged it about 20% dimensionally, just to be on the safe side.

Because I got my copy so late, December 20th 1974, I had to put in a rush building job to get a model of the Tiara ready for the Vegas Vultures New Year's Peanut Scale contest. I built my model with its landing gear retracted, for two reasons; the good looking flight simplicity, and because Bill Warner always insists that we stick with the Peanut Hand Launched rules. I prefer ROG, but I figured I'd put myself into Warner's shoes by having a model that wouldn't take off.

The model justified my efforts and did 40 seconds, officially, under a 25 foot ceiling, to take second place. (I further claim that they had to go fly outside in order to get better flights ... I'd already used up my attempts.) Actually I got beat fair and square, considering it's a fun contest and Vegas is a gambling town, and my six-shooter was at home.

This model is really a very simple airplane to build and won't require too much in the way of instructions. Being a modern airplane, it does not have a lot of external details (like a bipe), and therefore it is important to add what details are readily apparent.

The horizontal and vertical tails are simply built over the plan, using 1/20th sheet, the tips are firm 1/16th sheet, and all the other ribs are 1/40th sheet (DON'T GET SHOOK!! At the end of this article we are going to tell you where you can gel special Peanut Scale wood in these dimensions). The fillets at the front and the trailing edge of the center section of the wing are solid wood.

The fuselage uses 1/20th sq for its basic box structure and 1/40th sheet for its formers aft of the nose. Note that the prop shaft is above the upper cross brace locations. The technique I used to build the fuselage was to put in the upper cross braces slightly forward of the former positions. Then, when the complete fuselage structure, including upper stringers, nose cowl sheeting, side fill-ins and bottom block were in place, I knocked all the upper cross pieces out of the structure, leaving plenty of room for the rubber motor. (That should be rubber engine? right, only the electric powered planes have motors.) (Why change after all these years!?)

The nose block is made up of two parts; a 1/4 thick nose and a 1/8 thick plug, made to fit in the nose of the model. Note that both front cross pieces are cut away so the plug can be inserted in the nose.

Cover the model with your favorite tissue and technique. This has been covered, forgive the pun, so many times in Model Builder that we'll leave covering unexplained here.

The aft canopy is a simple flat-wrapped sheet of thin clear plastic. The forward one must be formed either by stretching hot over a mold, or by doing the same thing with a Vacu-Form. The canopy on the model in the photos was made on a toy Mattel Vacu-Form. It is about as big as you can possibly do and took me three tries to get a good one.

Decoration and details come last. I used red and blue tissue for the stripes, black tissue for the numbers, (letters) and top of the cowl, and the simulated retracted main wheels. The nose wheel, fairings, flap hinges and carburetor inlet, and tail bumper are scrap balsa.

For a source of Peanut Scale wood for this model send a self-addressed stamped envelope to: Mike Taibi, 4339 Conquista Ave., Lakewood, CA 90713 for his price list.

Peanuts can be built lighter with specially cut wood and a light Peanut flies better and lasts longer.

The model in the photos flew best in left circles. The wings had 1/8 inch of washout and the trailing edge of the rudder was warped slightly for a left turn. Power was one loop of 1/8 rubber, 10 inch long."

Direct submission to Outerzone.

Quote: "Robin HR.100 Tiara; Peanut scale plan by Walt Mooney from the April, 1975 issue of Model Builder. The horizontal tail has been completely re-drawn and adjustments have been made to the length and leading edge of the main rib. Jan Novick."

Supplementary file notes

Article.
Transcript.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Robin HR100 Tiara (oz12721) by Walt Mooney from Model Builder 1975 - model pic

Datafile:
  • (oz12721)
    Robin HR100 Tiara
    by Walt Mooney
    from Model Builder
    April 1975 
    13in span
    Scale Rubber F/F LowWing Civil
    all formers complete :)
    got article :)
  • Submitted: 23/12/2020
    Filesize: 179KB
    Format: • PDFbitmap
    Credit*: JanNovick

ScaleType:
  • Robin_HR100 | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz12721) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Robin_HR100
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Robin HR100 Tiara (oz12721) by Walt Mooney from Model Builder 1975 - pic 003.jpg
003.jpg
Robin HR100 Tiara (oz12721) by Walt Mooney from Model Builder 1975 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • Robin HR100 Tiara (oz12721)
  • Plan File Filesize: 179KB Filename: Robin_HR100_Tiara_oz12721.pdf
  • Supplement Filesize: 1107KB Filename: Robin_HR100_Tiara_oz12721_article.pdf
  • Supplement Filesize: 16KB Filename: Robin_HR100_Tiara_oz12721_transcript.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.