Heath Parasol (oz12706)

 

Heath Parasol (oz12706) by Frank Ehling from Air Trails Annual 1958 - plan thumbnail

About this Plan

Heath Parasol. Free flight scale model.

Quote: "Heath: Fine scale free flight for .02 power.

Ed Heath's Parasol was once one of America's most popular planes. There were several versions of this light plane including the midwing and low wing. The Parasol shown here offers the model builder a fine stable configuration for free-flight scale. A high wing position, long nose and good wheel location combine to make this a fine flyer.

Our first job was far too light for the surprising power output of Cox's Pee Wee engine, so a second model was made heavier, stronger and well doped. Heavy wheels were added and hard balsa used throughout bringing the total weight to seven ounces. This gives the model fine scale like flight performance. A nice touch is to make the elevators and rudder movable; this is a great aid in trimming the model for flight.

Start the fuselage by cutting the sides and bulkheads from 1/16 sheet. Cement the rear fuselage sides together; add the bulkheads starting from the rear and working forward; done this way the fuselage is made with little difficulty.

Wing mounts are bent from 1/16 - wire, thread-bound and cemented to 1/4 in square balsa, then cemented in position. The landing gear is also bent, bound and cemented in place after which the remaining bulkheads and stringers are cemented in place. Sheet the nose section checking that the grain runs as prescribed on the plans. Cowl blocks are carved and hollowed enough to accommodate your engine. (Fiber glassing the interior of the nose and cowl with cloth and resin will aid fuel proofing). Dress snaps and a dowel hold the cowl in place. (You remove cowl when starting engine.)

Wing is made in the usual manner; the four center ribs are bass or other hardwood; a brass tube is bound to them as shown on the plan. Note 'A' indicates the ribs are bound with thread and cemented together. Two small brass tubes are soldered to the wing mount. A balsa dowel is used to join the wing to the mount. In a rough landing this dowel will break and save the model from damage. Add center panels of celluloid to wing before covering.

The tail assembly is flat and can be made directly over the plan. If adjustment hinges are to be used these should be cemented in place before covering.

Cover the entire model with Silkspan. The wing struts are made from bass or very hard balsa cemented together and then sanded. All hooks are cemented and thread-bound. We used Ambroid to get a strong job.

Before flying check to see that the CG is as indicated on the plan. Adjust elevators until a good glide is achieved. Fly with little power until the model is performing as desired. A little rudder adjustment goes a long way."

Direct submission to Outerzone.

Supplementary file notes

Article pages, thanks to RFJ.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Heath Parasol (oz12706) by Frank Ehling from Air Trails Annual 1958 - model pic

Datafile:
  • (oz12706)
    Heath Parasol
    by Frank Ehling
    from Air Trails Annual
    1958 
    34in span
    Scale IC F/F Parasol
    all formers complete :)
    got article :)
  • Submitted: 18/02/2020
    Filesize: 272KB
    Format: • PDFbitmap
    Credit*: Circlip, RFJ

ScaleType:
  • Heath_Parasol | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz12706) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Heath_Parasol
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Heath Parasol (oz12706) by Frank Ehling from Air Trails Annual 1958 - pic 003.jpg
003.jpg
Heath Parasol (oz12706) by Frank Ehling from Air Trails Annual 1958 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

Surely it was designed by Frank Ehling, one of the many plans published under no name or different name. He was a designer editor in the staff of Air Trails as stated in this annual issue too.
pit - 29/12/2020
Thanks Pit, ok am setting this one as by Frank Ehling.
SteveWMD - 29/12/2020
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.