Sopwith Pup (oz12615)

 

Sopwith Pup (oz12615) by John Blair from Model Builder 1978 - plan thumbnail

About this Plan

Sopwith Pup. Peanut scale rubber model.

Quote: "One of the winners in our 1976 Parcel Post Proxy Peanut contest, this excellently detailed model is on permanent display in Model Builder's office. Also a fine flier.

The Sopwith Pup is universally considered to be one of the all-time classics in service from 1916 to 1917, it performed with considerable success; its superb maneuverability and ruggedness enabled the Pup to remain effective in action even after its speed and armament had been far surpassed.

The Pup also scales down well. Its proportions and flying qualities as a peanut are delightful. It looks 'right', sitting on the table or circling overhead.

Along with most aircraft of the period, the Pup's construction was very model-like, and can be reproduced almost piece-for-piece without much sacrifice of flying ability. The plans, then, show almost exact scale structure, especially in the wings and tail. If a lighter, simpler model is desired, such details as false ribs and aileron structure may be omitted, and the ribs spaced farther apart. Built as shown, the model will weigh approximately .75 oz; carefully omitting part of the structure could reduce this to .50 oz or less.

The construction may be as straightforward or complicated as your choice of detail demands. The first step, however, is a departure from the customary. Begin by preparing some non-stock wood. If no balsa stripper is available, careful work with a good straightedge and a very sharp Uber Skiver will be OK. Prepare a supply of 1/32 x 1/16 strips for fuselage cross-members, stringers, wing spars, etc. Some 1/32 x 3/32 is required for elevator ribs and spar, and some 1/32 x 1/8 is needed for strut fairings. Sand a piece of 1/32 sheet down to about 1/64, for wing ribs and fuselage top decking. Strips of 1/32 x 1/16 basswood are required for laminating the flying surface outlines.

The fuselage "box" is built with 1/16 sq longerons, The first three bays from the the nose have 1/16 sq cross-members; from there back, use 1/32 x 1/16, except for the tail post. After former 1-A is positioned on the nose, remove bottom cross-pieces 1 and 3, and install the landing gear wire, with formers 1-B and 3-B sandwiching the wire in place.

Next, install the cabane strut wires by gluing them directly on the top longerons. The top decking will cover and strengthen this joint. The top decking may be installed as one piece, but the side, from 1 to 2-S, is a compound curve, and will have to be planked with 1/32 x 1/4 strips. From 2-S back, the side streamlining is completed by three short 1/32 x 1/16 stringers, and is tissue covered. A corner of the side sheeting will have to be cut away to install the lower wing root rib, which is part of the fuselage..."

Direct submission to Outerzone.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Sopwith Pup (oz12615) by John Blair from Model Builder 1978 - model pic

Datafile:
  • (oz12615)
    Sopwith Pup
    by John Blair
    from Model Builder
    September 1978 
    13in span
    Scale Rubber F/F Biplane Military Fighter
    all formers complete :)
    got article :)
  • Submitted: 27/10/2020
    Filesize: 284KB
    Format: • PDFbitmap
    Credit*: MB2020

ScaleType:
  • Sopwith_Pup | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz12615) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Sopwith_Pup
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Sopwith Pup (oz12615) by John Blair from Model Builder 1978 - pic 003.jpg
003.jpg
Sopwith Pup (oz12615) by John Blair from Model Builder 1978 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.