Control Line Model (oz12614)

 

Control Line Model (oz12614) by Vic Smeed from Working Models 1964 - plan thumbnail

About this Plan

Control Line Model (no name). Control line trainer model.

Note this is not a full size plan. This is a scan of the drawings as they appeared in the pages of the book, as printed.

Note this plan (and build instructions) are excerpts from the Vic Smeed book 'Working Models', thanks to Mary at https://rclibrary.co.uk/title_details.asp?ID=1195.

Quote: "Chapter Five: A Control-line Model for 1/2 to 1 cc.

CONTROL-LINE model aeroplanes can be flown in a much more restricted space than freeflight models, since the main requirement is a circle clear of obstructions, of only about a hundred feet in diameter or, in the case of this little model, a maximum of fifty feet in diameter. For this reason it is usually unnecessary to travel out into the country to fly control line, but by the same token it is easier to cause a nuisance with this type of model; nothing can be more irritating to someone trying to have an afternoon nap than the continual whine of a small engine running near at hand. It must also be remembered that the model can fly overhead to the extent of the lines, and even 25 ft plus the height of the flier can bring the model in contact with overhead electric wires. About a dozen modellers have been killed or severely burned by foolishly flying near overhead power lines. It therefore pays to find a suitable space away from houses and hazard. It is very nice to be able to take a model off from the ground since this makes control considerably easier if you have never flown one before, but even in a field of rough grass an old piece of linoleum or roofing felt will make an adequate runway.

The method of controlling the model is almost universal; two lines run from a handle held in the hand to two lead-out wires attached to a bellcrank in the model. Movement of the handle swings the bellcrank and at 90 degrees to the lead-outs a push-rod is connected to a horn on the elevator, thus moving the elevator up and down and controlling the model in pitch. A stable model is not therefore necessary provided that balance is within certain limitations. If the model is capable of staying out at the end of the lines no stability problems will arise.

Start construction by laying out the wing. This is a piece of 18-in x 3-in x 1/16-in balsa, to the back of which is glued a triangle 18 in x 1-1/2 in at its maximum. The joint should be glued along its whole length, and the wing panel then pinned down on a flat board with a sheet of grease-proof paper covering the board to prevent the cement from sticking to it. Cement a length of 1/4-in square hard balsa to the leading edge, (the straight side of the sheet) then cut the ribs R1, 2, 3 and 4 (two of each will be needed) and cement in place. A second sheet of 18-in x 3-in x 1/16-in is now glued over the top of the ribs and a second triangle glued on to the back to complete the wing upper surface. When the cement is completely dry, sand the whole wing smooth and round off the leading edge as shown in the drawings; the tips can also be rounded off slightly.

Now cut two fuselage sides by drawing one out on a sheet of 1/8-in balsa, cutting this and using it as a template for the second sheet. Also cut bulkhead B3, then cement the fuselage sides over the wing and insert B3..."

Direct submission to Outerzone.

Quote: "Hello Outerzone! Hope everyone is doing well? My latest build a Vic Smeed design. One of his few c/l models. From the book, Vic Smeed 'Working Models'. It's in your library section. Fitted with a DC Bantam. If anyone is thinking of building one I would suggest moving the wing back 1/2 in because there is very little room for the fuel tank and to get the CG in the right shop it’s going to need a good bit of lead up front. Best regards, Tony Wright "

Supplementary file notes

Article (chapter 5 of the book).

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Control Line Model (oz12614) by Vic Smeed from Working Models 1964 - model pic

Datafile:
  • (oz12614)
    Control Line Model
    by Vic Smeed
    from Working Models
    1964 
    18in span
    IC C/L LowWing
    all formers complete :)
    got article :)
  • Submitted: 08/11/2020
    Filesize: 1452KB
    Format: • PDFbitmap
    Credit*: TonyWright

Control Line Model (oz12614) by Vic Smeed from Working Models 1964 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.