Broussard MH-1521 (oz12586)
About this Plan
Holste MH-1521 Broussard. Peanut scale rubber model.
Quote: "The Broussard MH1521 was picked by the author as an ego-pleasing, fun flier, not just another contest Peanut! If you are tired of the same old fare in Peanuts, put a little salt in your diet!
A number of years ago, people built Peanut scale models of all types of full size aircraft, even almost unflyable types, because they wanted a model of 'that' airplane. They would go ahead and build them anyway because even if they didn't fly too well, they would still have a scale model of a plane that they always wanted to build without spending much time or money.
Now you don't see anything but Peanuts of aircraft that have near perfect proportions for rubber scale, that is, at contests you don't. Some people still build models of what they want instead of what will place in a contest. Bill Hannan is a wonderful example. He designs models of whatever he wants to build. Some of his designs fly competitively, others are just for fun. The model presented here is an attempt to capture the same flavor that Mr. Hannan's BD-4 and Aristocrat have. Those Peanuts are tiny-winged delicacies, and they are my idea of what a Peanut should be.
So, if you find time between Lacys to build this model, I hope you like it.
The MH 1521 Broussard was built by a small, French company, Avions Max Holste, between 1952 and 1968. It was, and still is, used by the French army as a utility transport. They have been used to spray crops and carry supplies in several African countries, so a color scheme should be no problem. (Mine is Imaginary French Air Force).
To build this model you might start with the tail surfaces, to get you into the building mood. Use good, firm wood on the twin vertical tails, they take a beating out there on the ends of the horizontal tail.
When building the horizontal tail, please be careful to get the end rib square to the spar. This will keep the fins straight. The wings are very simple, and should give you no problems. Just be certain that you use hard wood for the leading edge, to prevent dents.
When you have it up off the board, then you can add the skylight. Use very thin cellophane for this to keep the weight down.
The fuselage is next. Once again, pick hard wood for the highest stressed part, the longerons. Add the side windows before you cover the fuselage. The cowl is made of balsa which is rolled around a pair of formers which are held together by four keels. Add the front balsa rings to build up wood for the round front. Cut a key to fit the hole in the ply former, and add the balsa nose button and bearing. A Peck Polymers nose bearing worked for me, it helped give me the needed clearance when I added downthrust.
My model was covered with domestic tissue, the only tissue I had in olive green. If you can find it, you will be better off covering a model this small with Japanese tissue instead of the coarser domestic tissue. You might try dyeing white Japanese tissue to get green, or airbrushing it with acrylic artist's paint as I did on the cowling.
After you have it covered, but before you assemble it, add the trim details, and the surface outlines. It is easier to work on the model while it's in pieces than after it's assembled. Paint the struts, windshield frames, and cowling before you add them. Assemble the model very carefully. Alignment of the twin fins is very important.
Balance the model on the spar, adding as much clay as it takes to make it balance. Test glide the model over short grass, if you use long grass, as some of the other articles say, you will not be able to watch the model's flight for very long before the grass gets it. Once you have the glide right, start with about 100 turns on a ten-inch loop of 3/32 rubber and more down-thrust than you think you will need.
This model, because of its small tail, will need a bunch of down-thrust. Let it circle the way it wants to, unless you fly indoors, then you will have to fly it left. Don't expect more than about 30 seconds from this model unless you build it a lot lighter than the plans show.
I hope that after you build this model you like it enough to build more non-contest type models. I think we need to put the spice, er, salt back into Peanut scale."
Direct submission to Outerzone.
Quote: "Peanut scale Max-Holste MH-1521 Broussard by Steve Gardner from the August, 1983 Issue of Model Builder. Original plan has been modified by shifting the rear motor peg forward for better balance."
Supplementary file notes
Did we get something wrong with these details about this plan (especially the datafile)?
That happens sometimes. You can help us fix it.
Add a correction
Max_Holste_Broussard | help
see Wikipedia | search Outerzone
ScaleType: This (oz12586) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.
If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.
ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Max_Holste_Broussard
Wikipedia page addresses may well change over time.
For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.
Do you have a photo you'd like to submit for this page? Then email email@example.com
User commentsNice cleaning work, thank you.
Miguel - 09/11/2020
Add a comment
* Credit field
The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.
This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.
© Outerzone, 2011-2020.
All content is free to download for personal use.
For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.
Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.