Bellanca Pacemaker (oz12580)

 

Bellanca Pacemaker (oz12580) by Walt Musciano from Air Trails Annual 1951 - plan thumbnail

About this Plan

Bellanca Pacemaker (Transatlantic Bellanca). Control line scale model for class A engines.

The subject prototype is the CH-300 'Cape Cod' (Registration: NR761W) flown by Russell Boardman and John Polando from New York City to Istanbul in 1931.

Quote: "Remember the Pacemaker that flew from New York to Istanbul? This model of her is for Class A engines. Transatlantic Bellanca, by Walter A Musciano.

Clarence Chamberlin, Francesco Di Pinedo, Russell Boardman, Holger Hoiriis and James Mollison are a few of the famous pilots who selected Bellanca airplanes for their long-distance flights. World-famous names like Columbia, Liberty, Cape Cod and Irish Swoop all belonged to Bellanca designs.

Although we built the Cape Cod model with considerable success, the plans also describe the minor revisions required to construct the Liberty, another famous Bellanca, in case you prefer it to the Cape Cod.

Designed as both a stunt or sport job, our prototype model behaved beautifully as either by adjustment of control horn moment arm. Flown on 45 ft lines; the 152 sq inch wing area gives plenty of lift for contest type maneuvers. Any engine from .099 to .19 can be used to power this 3/4 in = 1 ft scale model. We mounted the engine pancake fashion so the nose profile would not be spoiled by the cylinder and to improve engine performance during quick changes in flight attitude (inverted flight).

Cut fuselage sides and formers from specified stock and cement fuselage together at rear. When dry, cement formers between sides one at a time starting from rear. Add bulkhead and cement mounts.

Tail surfaces are cut out and sanded to streamline cross-section. Cement elevator halves to hardwood joiner; add a commercial control horn with two holes. Hinge elevator assembly to stabilizer with crinoline strips. Cement stabilizer to fuselage; use plenty of cement. Attach music wire lead-out lines to dural bellcrank; screw or bolt bell-crank to bottom of top engine mount. Install wire control rod.

Although landing gear construction may seem unorthodox, it provided excellent service and is easy to make. Draw strut outline on du-ral sheet; cut out with tinsmith shears or fine hacksaw. File edges smooth, finishing with emery cloth. Drill holes for wire axle and mounting screws. Mount strut after bend-ing to shape; cement foundation securely to fuselage. Add axle strut. Cover fuselage bottom; add soft balsa nose blocks. Carve these to shape; remove from fuselage. Hollow as shown; re-cement in place after in-stalling fuel tank.

The wing is so simple it hardly need be mentioned. There is no dihedral, taper nor sweepback required. Cut out all the ribs and pin together. Sand these so they are of uniform shape. This improves appearance and performance. Separate ribs; pin them directly over wing plan. Add leading and trail-ing edges; block them up so they fit ends of ribs. Apply plenty of cement to all joints. Add solid soft balsa tips; when dry cut leading and trailing edges plus the tips to shape. Sand well and cover wing with paper. Apply three coats of clear dope sanding between with fine paper.

Cement wing securely to fuselage; then fuselage top can be added. Note that both top and bottom of fuselage should be applied with grain running spanwise. Install fin, offset rudder.

Pants are 'sandwiched', then carved and sanded to streamline shape. These slide over axle and fit to main strut. Install wheels before pants are cemented. Fillet the joint well with Plastic Wood or balsa-dust-and-cement mixture.

You may find a cowl ring made of aluminum or plastic that will fit. We made ours from balsa rings cut from sheet balsa and cemented together cross-grained under slight pressure. When dry the unit is carved and sanded to shape. Cowl-ring is cemented in place after painting model. If you have a lathe, the ring can be turned from hardwood.

Cut struts to streamline shape but do not install. Bend tailskid to shape, cement to fuselage. Model should receive at least two and preferably four coats of wood filler on all exposed wood surfaces. We used Testors Sanding Sealer. Sand-paper wood filler thoroughly after each coat has dried. Add control line guides on inboard wing tip.

Paint entire model yellow. We applied four coats; thinning each successive coat. Trim in black the wheel pant striping, cowl ring and upper portion of fuselage aft of cockpit plus license numbers. 'Cape Cod' lettering below cockpit and the map on fuselage side are white. These plus license are cut from 'Trim-Film.' Add cowl. Struts should be wood-fillered and painted yellow, then cemented in place. Coat all external surfaces, inside of fuselage near engine and engine mount cement joints with good grade of fuel proofer."

Direct submission to Outerzone.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Bellanca Pacemaker (oz12580) by Walt Musciano from Air Trails Annual 1951 - model pic

Datafile:
  • (oz12580)
    Bellanca Pacemaker
    by Walt Musciano
    from Air Trails Annual
    1951 
    33in span
    Scale IC C/L Cabin Civil
    all formers complete :)
    got article :)
  • Submitted: 18/10/2020
    Filesize: 348KB
    Format: • PDFbitmap
    Credit*: theshadow

ScaleType:
  • Bellanca_CH-300_Pacemaker | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz12580) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Bellanca_CH-300_Pacemaker
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • Bellanca Pacemaker (oz12580)
  • Plan File Filesize: 348KB Filename: Bellanca_Pacemaker_oz12580.pdf
  • Supplement Filesize: 458KB Filename: Bellanca_Pacemaker_oz12580_article.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.