Stinson Voyager 108 (oz12420)

 

Stinson Voyager 108 (oz12420) by Bill Schmidt 2005 - plan thumbnail

About this Plan

Stinson Voyager 108-1,2&3. Scale model for rubber power. Wingspan 22.6 in.

Quote: "This is my plan for you that I am putting out into the public domain. The other 17 plans of "Classic American Lightplanes" that were published in Flying Models Magazine in the late 90's thru the 2000's I still sell separately. Attached are pics of the Stinson 108-2 and -3 Voyager and Flying Station Wagon... Best, Bill Schmidt."

Direct submission to Outerzone.

Quote: "BUILDING INSTRUCTIONS. FUSELAGE: Start with the fuselage although you may prefer to do otherwise. Take the 2 main fuse side plates that the wings attach to and lay them on top of each other. They must match each other exactly! Now take a main wing rib that will glue to the side plates and sand and blend these all together using the lower wing spar stub square holes as the master datum reference index and will assure good alignment of the completed major assys. After this check is completed, you can begin to construct one of the 2 fuse sides.

Pin in place the main fuse sideplate very carefully over wax paper covered plan side view. Select a hard piece of 1/16 sq balsa for the lower longeron and fwd nose areas due to the hard loads to be encountered here. Cut and glue in the rest of the structure. Pencil the word 'inside R/H' on the fuse side plate.

When dry, remove and turn assy over and build the 2nd fuse side directly on pop of the 1st side to insure great accuracy of the 2 sides. Mark this 2nd side 'inside L/H'. When dry, remove and check your work. Due to variations in wood sizes, the pinned down side will be the flattest and better surface to be used of the model's fuse structure.

Lay 1 fuse side down with the note 'inside' facing you and glue 4 exact length stick crossmembers in the fuse constant width area dictated by the wing location. Lack of accuracy here, and the wings will sweep fwd or aft on final assy. Pick up this side with 4 sticks and place it sticks down on the other fuse side. Now, carefully glue each stick one at a time in its place. Make sure the notes 'inside' are inside. Now glue in the nose former generally denoted as Fl. Make sure it is straight viewed from the side and top.

Gently sand the 2 tail-ends of the fuse to a tapered 1/32 thickness and glue them together at the top only. This allows vertical alignment of the tailpost later on. Now glue in all the crossmembers and formers, top and bottom stringer locations are denoted with a starting place and an ending place by means of the master formers. The stringers are run in a straight line function between these formers. This guarantees a straight stringer installation with no ugly snaking.

Use a 1/16 thick sanding stick of ply or other hardwood to cut the notches in the intermediate formers. Now shim and sand the nose block retainer to fit snugly inside the nose former. With this in place lightly glue the noseblock to the retainer. Be careful not to glue this assy to the fuse..."

Supplementary file notes

Instructions.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Stinson Voyager 108 (oz12420) by Bill Schmidt 2005 - model pic

Datafile:
  • (oz12420)
    Stinson Voyager 108
    by Bill Schmidt
    2005 
    22in span
    Scale Rubber F/F Cabin Civil
    all formers complete :)
  • Submitted: 15/08/2020
    Filesize: 553KB
    Format: • PDFbitmap
    Credit*: BillSchmidt

ScaleType:
  • Stinson_108 | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz12420) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Stinson_108
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Stinson Voyager 108 (oz12420) by Bill Schmidt 2005 - pic 003.jpg
003.jpg
Stinson Voyager 108 (oz12420) by Bill Schmidt 2005 - pic 004.jpg
004.jpg
Stinson Voyager 108 (oz12420) by Bill Schmidt 2005 - pic 005.jpg
005.jpg
Stinson Voyager 108 (oz12420) by Bill Schmidt 2005 - pic 006.jpg
006.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

Thanks very much Bill Schmidt, for sharing this great design on OuterZone!
Dave D - 23/08/2020
Add a comment

 

 
 

Download File(s):
  • Stinson Voyager 108 (oz12420)
  • Plan File Filesize: 553KB Filename: Stinson_Voyager_108_oz12420.pdf
  • Supplement Filesize: 186KB Filename: Stinson_Voyager_108_oz12420_instructions.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.