Boston Tea Partly (oz12273)

 

Boston Tea Partly (oz12273) by Walt Mooney from Model Builder 1984 - plan thumbnail

About this Plan

Boston Tea Partly. Rubber sport model.

Quote: "The Boston Tea Partly is a relatively simple Bostonian that is designed with wing and tail structure that tends to resist warping by means of the diagonal ribs in the flying surfaces. It flies quite well, indoors and out. One consequence of this is the fact that there are no pictures of the author's complete model available. The author's model, the one that is shown as a skeleton, flew out of sight during an official flight in the San Diego Orbiteers versus Scale Staffel Bostonian Challenge on February 19, 1984, before he got around to having the finished model photographed.

The finished model with the red, white, and blue color scheme was constructed by Pete Glor. Although Pete's model turned out a little heavier than necessary, 38 grams with its rubber motor versus the 14 gram minimum allowed without motor, it also flies very well. It has recorded a 38-second official flight indoors under a less than twenty-five foot ceiling at a Scale Staffel flying session. Pete built his model for our traditional Fourth of July Bostonian meet, hence the color scheme and the license numbers on the model.

Another successful flying Tea Partly was made by Lenn Riddle who made a tricycle landing gear version by mount-ing the main gear one upright further aft, and adding a nose landing gear one bay forward of the main gear position shown on the plan. This model also flies very well and makes particularly smooth takeoffs and landings.

Keep your model as light as possible by using lightweight balsa, lightweight tissue, the thinnest plastic for windows, balsa wheels, and going easy on the dope.

The only thing much different about the structure of the Tea Partly than that of the ordinary Bostonian is the use of diagonal rib structure in the flying surfaces. These result in an amazingly stiffer structure. As a consequence, it's important to build the tail surfaces on a flat building board to prevent built-in warps. I like about an eighth of an inch of washout in each wing so the tip of the trailing edge of the wing should be blocked up this amount above the building board while constructing the wing.

The tail mid spars are added on both sides of the basic flat tail structure after it is removed from the board.

The wing dihedral starts on each side of the flat center section which is just as wide as the fuselage.

The fuselage is a conventional box made by building both sides directly over the plan. The sides are removed from the plan and carefully separated from one another using a thin blade. Cement them together at the aft end, and then add the cross pieces for the top and bottom of the fuselage, working forward bay by bay to the front end. The top and sides of the most forward fuselage bay are covered with 1/32 sheet balsa after adding formers 1 and 2 to the forward two cross pieces. The bottom of the forward two bays is covered with a solid balsa part carved from quarter-inch balsa sheet.

The nose block is made up from three pieces of quarter-inch sheet balsa. The forward two are carved after assembly to a shape simulating the forward end of an inline engine cowl. The aft piece is made to be a snug fit into the front end of the fuselage box. Drill a hole through the noseblock to accept one of the Peck-Polymers small nylon thrust buttons. Install your selected propeller, and add a carved spinner if desired.

Bend the landing gear wire to the shape shown, and securely cement it in place in the fuselage. Use lightweight balsa wheels and install wheel pants if desired. If your wheels are an eighth of an inch thick, the wheel pants can be made up using two pieces of 1/16 sheet balsa for the sides and a piece of 3/16 balsa for the center of each pant. Carve them to the shape shown in the top and side view, and carefully round off all the corners for a smoothly streamlined shape.

Fill in the bottom of the last fuselage bay with 1/32 sheet to support the thin wire tail skid. A short piece of 1/16 diameter aluminum tubing is used for the rear motor peg.

Cover the model using lightweight tissue. Use any color scheme you desire. Outdoors, a brightly colored model is easier to find.

Indoors, Pete Glor was using a loop of 3/16 flat rubber that was twenty inches long for his 38-second flight. I was using a loop of 1/4 flat rubber the same length on my last outdoor flight. You'll note in the pictures that Pete was using a drag flap on the left wing to tighten the flight circle and keep the model from hitting the basketball court walls.

The model should balance with the centerline level when supported half-way between the spars. Have fun at your Tea Partly."

Direct submission to Outerzone.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Boston Tea Partly (oz12273) by Walt Mooney from Model Builder 1984 - model pic

Datafile:
  • (oz12273)
    Boston Tea Partly
    by Walt Mooney
    from Model Builder
    June 1984 
    16in span
    Rubber F/F Cabin
    all formers complete :)
    got article :)
  • Submitted: 01/06/2020
    Filesize: 348KB
    Format: • PDFbitmap
    Credit*: MB2020

Boston Tea Partly (oz12273) by Walt Mooney from Model Builder 1984 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.