Towline Glider (oz12254)

 

Towline Glider (oz12254) by EG Currington from Air Trails 1951 - plan thumbnail

About this Plan

Towline Glider.

Note this unnamed Nordic glider by EG Currington was the winner of a 1951 Air Trails model design contest.

Quote: "TOWLINE GLIDERS. English designer scores victory over all contenders in AT's model towline glider contest; Nordic-type craft features novel wing and stab mount.

While the sky-rocket climb of a powered model may be exciting, nothing can give more satisfaction than the graceful maneuvers of a towline glider being borne aloft by a friendly thermal.

In America we handicapped gliders for years by allowing only 100 feet of towline and requiring a tremendous fuselage cross section. In contrast the Europeans could use more than 300 feet of towing line and a very slim fuselage. Yet we managed to rack up some surprisingly high times. The short towline led us to develop gliders that were distinctly different from the Continental type. We found that 100 feet of towline does not give the model much time for thermal hunting. Ground disturbance is high and thermals are always scattered. The model must of small up-lift areas. Characteristics of such a glider are short coupled wing and stab, and relatively large dihedral.

On the other hand, 300 feet of towline allows a more leisurely, roaming flight to pick up fully developed thermals or to obtain optimum glide. Such conditions do not require super-stability or exceptional spiral control. Hence, the basic Continental design has a relatively long moment arm and small dihedral. Incidentally, our rules are now more reasonable: 200 foot of tow-line and length 2/200 fuselage cross section.

While a tight circling glider may take full advantage of an individual thermal to go out of sight straight up, a roaming Continental design will go out of sight on the horizon. A sort of bouncing trip from one thermal to another in honey bee fashion. You can see that conditions determine the regional design.

While we were developing our own style of glider design, the Scandinavian flyers came up with something a little different. The basic characteristics were a very slim fuselage, long moment arm, thin but deeply undercambered airfoil and small tail surfaces. Another characteristic which is especially noticeable to the American builders is the comparatively small tip dihedral 'area' used at high angles.

At first Scandinavian glider sizes varied, but there was gradually formulated a design now known as the 'Nordic A/2'. They found that when all requirements - building time and cost, transportation and performance - were considered, a glider having a total surface area of between 495 sq in and 526 sq in will give the best return for the time and money. The standard FAI fuselage cross section formula, Wing Area/100, is used.

This month's winning towline glider design is based on the Nordic formula. The designer is not a Scandinavian, but an Englishman, EG Currington, from Manchester. The English model builders have adopted this particular type of glider whole-heartedly, and they are going in strong for the category.

This design has many features not normally found on our type of gliders, such as the tongue and box connection of the wing to the fuselage. It is a feature that should be investigated. The tendency for many builders to progress from small size to larger sizes is eventually brought to a stop when the 12 foot wing just doesn't fit into the subway or family car. This design will be a good start on which to test the tongue and box connection.

Aerodynamically, the model follows the basic Nordic design: small tip dihedral and long moment arm. Structurally, it has a simple monocoque fuselage which will take care of all sorts of landings.

Start construction with the wing as you will need it to line up the fuselage. Cut the ribs. Make a metal rib template.

The tongue-box must be made to fit the tongue well, but without binding. If you have no silk, wrap the box with thread and coat with cement. When fitting the boxes to the wing halves, assemble the two halves on the tongue. Place the wing on a flat surface. Line-up the leading edges so that they will be in a straight line. Make sure that both halves are lying flat on the surface. You can now let the cement set. Before sliding the boxes through the ribs, coat with cement the sides of the spars and the edges of the boxes.

After the initial cement has set, apply another coat at all contacts between the wing portion and the plywood box. When that has set for several hours, remove the wing from the jig, and apply cement at the bottom portion.

Make the stabilizer. You will need it to obtain an approximate balance while the fuselage is being constructed..."

Direct submission to Outerzone.

Supplementary file notes

Planfile includes article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Towline Glider (oz12254) by EG Currington from Air Trails 1951 - model pic

Datafile:
  • (oz12254)
    Towline Glider
    by EG Currington
    from Air Trails
    August 1951 
    59in span
    Glider F/F
    all formers complete :)
    got article :)
  • Submitted: 06/06/2020
    Filesize: 637KB
    Format: • PDFbitmap
    Credit*: rchopper56

Towline Glider (oz12254) by EG Currington from Air Trails 1951 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.