Yak-9D (oz11952)

 

Yak-9D (oz11952) by HC Quek from Aeromodeller 1971 - plan thumbnail

About this Plan

Yak-9D. Control line stunt model.

Quote: "YAK-9D. Semi-scale control-line stunter for 5.6 cc engines. Designed by HC Quek.

WHY THE YAK 9D? Unlike the Spitfire, Mustang or the Hien, the Yak 9D has so little to offer in terms of character! However, though simple both in profile and plan form, the Yak 9D was one of the very successful Yak series of Soviet aircraft during the second World War.

From the modeller's point of view, the simple lines provide an ideal subject for an easy-to-build, semi-scale model. The design presented here is far from scale, but well finished and decorated should provide immense eye appeal.

Basically, it is a slab-sided model, with no gimmicks in the design. The prototype model had an overall span of 58 in and used full span flaps. After flight tests the span was reduced by 3-1/2 in and the flaps subsequently reduced to just two thirds of the span - these two vital modifications were found to contribute towards improving both level flight and square manoeuvres. Wing fairings were added to the original model to improve its appearance.

It is always worthwhile making a careful selection of the various grades of wood required. Using very carefully selected wood the weight distribution was found to be just right on the original model no ballast being necessary to achieve the correct centre of gravity position. Carefully cut out all the wing ribs from light quarter-grain wood. The sections used are grossly modified NACA 0018 airfoils varying in percentage thickness from R1 to R14.

The wings are built flat on the building board. Pin the bottom 3/16 sq main spars in position, then pin all the ribs in position. Level up the TE of the ribs with scrap pieces of balsa. Next mark and insert the 3/16 sq top spars. Pin 1/4 in sq to trailing edges of the ribs and 3/8 sq to leading edges of ribs - still without using any glue. Check alignment and when satisfied that it is absolutely true - with no twists etc, spot cement all the cross points and allow to dry thoroughly. Finally, cement top 1/2 x 3/16 in joiner in position.

With the wings still pinned to the board, add the 1/16 LE and TE sheeting to the top surface before cap stripping the ribs with 3/16 x 1/16 soft balsa.

When dry, remove from board, turn over, and preferably pin wings to the board to check alignment. Add the 1/2 x 3/16 in joiner and secure the wing tip weight as shown. Sheet the LE and TE and add the cap strips as before. Sheet cover underside of centre section. When dry, remove wings from boards and build on the wing tip.

Sand TE of wings to section shown. Cut and sand flaps to section, add flap horn, then hinge to wing. Install the bellcrank mount complete with the control assembly. Connect the bellcrank to the flap horn with a 16 swg pushrod, before sheeting the top of the centre section. The complete wing may now be sanded thoroughly all over..."

Yak 9D, Aeromodeller, February 1971.

Direct submission to Outerzone.

Supplementary file notes

Article pages, thanks to RFJ.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Yak-9D (oz11952) by HC Quek from Aeromodeller 1971 - model pic

Datafile:
  • (oz11952)
    Yak-9D
    by HC Quek
    from Aeromodeller
    February 1971 
    54in span
    Scale IC C/L Military Fighter
    all formers complete :)
    got article :)
  • Submitted: 30/10/2019
    Filesize: 955KB
    Format: • PDFbitmap
    Credit*: Circlip, RFJ

ScaleType:
  • Yakovlev_Yak-9 | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz11952) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Yakovlev_Yak-9
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Yak-9D (oz11952) by HC Quek from Aeromodeller 1971 - pic 003.jpg
003.jpg
Yak-9D (oz11952) by HC Quek from Aeromodeller 1971 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.