Miles M77 Sparrowjet (oz11937)

 

Miles M77 Sparrowjet (oz11937) by Geoff Andriessen from RCME 1988 - plan thumbnail

About this Plan

Sparrowjet. Scale PSS slope soarer.

Quote: "LET US HOLD A MEETING for PSS models. After all, club members already possessed some. A Spitfire and a Hunter came to mind, so surely there must be others already in existence or maybe on the drawing/building board.

It soon became apparent that my arguments for PSS would be considerably enhanced if I put my money where my mouth was! But I like something different! Don't I? Furthermore it had to be something quick and easy to build, fairly cheap and especially no jiggery-pokery (or not much) with wing and tail areas, fuselage cross-section and so forth.

After considerable searching I happened on a design which, against all my expectations, fulfilled the requirements. Even more so: how about a twin jet racing aircraft with a fixed undercarriage, which was converted from a piston-engined aircraft also designed as a racer.

Mr and Mrs FG Miles built the M5 Sparrowhawk in 1935 and it was a 'circuit of Britain' King's Cup contest. In 1951-53 Mr. F. Dunkerley had F. G. Miles transfo the aircraft to a light jet racer, again to talc part in the King's Cup and other races. At Shoreham, for example, it averaged 210 mph (5 miles faster than the New Gull in the same race) to place 7th on handicap in the Goodyear Trophy. Later that day in the round-the-aerodrome TBU (Throttle Benders Union) race the Sparrowjet averaged 185 mph into 3rd place.

Anyone interested in further details of this fascinating aircraft will find them as Plan 2292 in the Scale Drawing Plans Handbook, which I enlarged to provide the basis for the model. This model, although scale, lends itself to the almost standard construction of most slope-soarers. The tail surfaces are of 1/4 in sheet balsa, the wings are foam veneer or 1/16 balsa sheet, and the fuselage is 1/8 sheet sides doubled with 1/64 ply, sundry chunks of block or thick sheet are used for nose, nacelles etc.

Construction: Tail Surfaces: You see the results most rapidly here! Cut out from some nice light 1/4 in sheet and sand to a pleasing aerofoil, I leave a square cut trailing edge on the rudder and elevators some 3/32 in thick as an antiflutter measure. The fin and horizontal stabiliser are each half slotted so that they may be assembled and checked with a square prior to gluing. A word about glue. My preference is to use a fairly flexible white glue for most joints and a hard aliphatic one where it will be necessary to sand. (I do use superglue at times for 'spot-welding').

Carefully mark the auxiliary fins location, then position them accurately with the aid of a small square and 'spot weld' them on with a suitable cyano superglue. Drill holes through stabiliser and into fins, dowel on with cocktail sticks or something similar. Hose some white glue around the joint for the long term bond.

Do take all precautions with any cyano glue, use a different glue if affected at all! The elevators are bottom hinged (it looks better when the model is on the ground) and this is best done at or after the covering stage. This hinging also applies if you require a working rudder, although the model is really intended for two function only.

Fuselage: Now here (as they say) is something to get your teeth into. Transfer the fuselage outline onto a sheet of 1/64 ply. Ignore the wing cut-out for the moment. Now get a nice large sharp pair of scissors - and make sure that you are able to resharpen and replace them before they are missed - cut out the fuselage side. It is possible to do this most quickly and accurately.

Now use this first side to mark out the other 1/64 ply side and also the 1/8 balsa sides and cut out these. No, you do not use scissors on the 1/8 balsa!

Using a contact adhesive, such as Copydex glue, stick the ply and balsa side pieces together, ensuring that you finish up with one left side and one right side. The ply goes on the outside. It is convenient to leave the balsa pieces slightly oversize in the nose area to facilitate subsequent shaping. Now cut out the wing seating with a fretsaw after clamping both sides temporarily together.

The fuselage very conveniently jigs itself if you build it upside down, like this: The top rear decking is made from two light pieces of 1/2 x 3 in sheet. Mark the plan view of the fuselage and the position of the bulkheads on the underneath of the lower piece, now mark a line about 1/2 in towards the centre following the outline from the front of the tail unit to the front of the wing. Next cut down the centre line of this piece and cut out the inner section. Remove a 1/4in strip for the fin.

It is now easily possible to razor plane the inner edges to about 45°. Assemble and stick to the top piece and you will find that you now have a hollowed-out rear decking. Do not shape the outside edge at this stage because, if you lay the decking down on its top, you will see that the two fuselage sides will sit on it. The whole lot now being upside down.

Before fixing the fuselage sides to the top decking we need some spacers or jigs. These are very conveniently made by constructing the bulkheads. Each bulkhead is rectangular and is made from 1/8in balsa faced with 1/64 ply. Ensure that these are perfectly square (yes I know that I just wrote rectangular, how about true, then?) because the accuracy of the fuselage will depend on them.

Position the bulkheads B and C on the rear decking and tack with superglue, after checking uprightness with a square. The two fuselage sides may now be offered up and tacked to the bulkheads B and C. Draw in the rear fuselage sides to the marks previously made and pin to retain (now you know why we did not chop off that surplus wood). Tack in the remaining rear bulkheads D and E and use white PVA to glue all joints. Leave to dry overnight and then add the 3/32 rear fuselage floor with the grain running across the fuselage..."

Sparrowjet, RCM&E, March 1988.

Direct submission to Outerzone.

Supplementary file notes

Article pages, thanks to RFJ.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Miles M77 Sparrowjet (oz11937) by Geoff Andriessen from RCME 1988 - model pic

Datafile:
  • (oz11937)
    Miles M77 Sparrowjet
    by Geoff Andriessen
    from RCME
    March 1988 
    43in span
    Scale Glider R/C Racer Civil
    all formers complete :)
    got article :)
  • Submitted: 30/10/2019
    Filesize: 574KB
    Format: • PDFbitmap
    Credit*: Circlip, RFJ

ScaleType:
  • Miles_Sparrowjet | help
    see Wikipedia | search Outerzone


    ScaleType: This (oz11937) is a scale plan. Where possible we link scale plans to Wikipedia, using a text string called ScaleType.

    If we got this right, you now have a couple of direct links (above) to 1. see the Wikipedia page, and 2. search Oz for more plans of this type. If we didn't, then see below.


    Notes:
    ScaleType is formed from the last part of the Wikipedia page address, which here is https://en.wikipedia.org/wiki/Miles_Sparrowjet
    Wikipedia page addresses may well change over time.
    For more obscure types, there currently will be no Wiki page found. We tag these cases as ScaleType = NotFound. These will change over time.
    Corrections? Use the correction form to tell us the new/better ScaleType link we should be using. Thanks.

Miles M77 Sparrowjet (oz11937) by Geoff Andriessen from RCME 1988 - pic 003.jpg
003.jpg
Miles M77 Sparrowjet (oz11937) by Geoff Andriessen from RCME 1988 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.