DH 60 Cirrus Moth (oz11723)

 

DH 60 Cirrus Moth (oz11723) by David Boddington from RCME 1985 - plan thumbnail

About this Plan

DH 60 Cirrus Moth. Scale model for radio control.

Quote: "A sport scale DH60 Moth at around 1/8 scale (46.5 in span) that was presented free with the December 1985 RCM&E. No designer accreditation but I think it has all the hallmarks of a Boddington special... If so I suspect it may be a model that was very popular at the time for early electric conversions. I've included two versions of the plan - one authentic original as it was presented at the time (rather cramped to fit the small single sheet and with several bits that needed to be cut and stuck on) and one that I've edited for convenience. No article unfortunately, but maybe someone will find them! [edit: found now, see below]"

Direct submission to Outerzone.

Note we have set the edited plan (more convenient layout) as the primary download file.

Update 17/11/2019: Added article, thanks to KLH.

Quote: "A near scale DH 60 Cirrus Moth for .15 - .20 engines and 3-function radio control.

Introduction: The DH 'Moth' was one of the most successful light aircraft of all time and was used to break many of the existing duration and distance records for aeroplanes of that category. Few changes have been made to the model to affect scale accuracy, a revised wing section is used and the nose cowling has been simplified (the 'Cirrus' engine version has been selected, although the model could be adapted for the 'Gipsy' or 'Hermes' versions). No ailerons are fitted, with the scale dihedral used, the rudder gives excellent control and ailerons would have only limited effect.

The prototype was flown with a Veco 19 engine and this proved to be more than adequate in power, a high performance .15 would certainly be sufficiently powerful and a 20 size four-stroke engine ideal. Use a large diameter fine pitch propeller (ie 9 x 4, or 10 x 3-1/2) to keep the engine speed low and provide good ground acceleration.

Construction: Read the instructions through completely and check through all the parts and identify them with the plan White glue (PVA) may be used for all construction except for wood/ metal joints, where a slow drying epoxy should be used. Excessive application of glues adds unnecessary weight - the strongest joints result from accurately mating surfaces and minimum adhesive. Protect the plan with clear plastic or wax rubbed on the drawing.

Wings: The upper and lower wings are basically the same except for the centre section units, the outer panel root sections and the interplane strut fittings. Note that the lower wing spars extend to the wing tip. top spar terminates at the tip rib. Upper and lower wings are constructed in three panels - port, centre and starboard - and joined with dihedral braces at a later stage.

Pin down the 3/16 sq lower spars and lower 1/16 x 1 in trailing edge strips to the port and starboard panels for the lower wing. Glue the wing ribs and 3/32 ribs ensuring that all ribs are vertical, except the root rib which should be angled to the dihedral template Glue the 3/16 sq top spar and leading edge into position plus the 1/16 x 1 in top trailing edge. The 1/16 x 1 in vertical grain webbing is fitted to the first two root rib bays and thence in alternative bays. Butt joint the 1/16 x 2 in leading edge sheeting to the top spar glue to the ribs and to overlap the leading edge. Join wing tip pieces and set aside to dry.

Fill in between the trailing edge strips at the two root bays and tip area with 1/4 x 3/4 in trailing edge stock reinforcement. Build up the lower spars at the tip with 3/16 x 1/4 in at the front and 3/16 sq at the rear spar to give the wing tip a cambered section (this improves the appearance of the model when viewed from the side). Add 3/16 x 3/8 fairing pieces to the upper surface of the tip.

Interplane strut fixings are produced by drilling a small hole (1/32 in) in the 1/4 in sq hardwood crosspiece inserting a small split pin bending over the ends of the pin above the hardwood and epoxying in position. When the panels have been removed from the building board - when the glue has thoroughly dried - and sanded, the strut fixings can be glued in position with the upper surface of the supports lining up with the upper edge of the ribs and sheeting. Reinforce the ends of the hardwood with scrap balsawood where they butt joint onto the ribs.

Make up the port and starboard upper wings in a similar manner but with the addition of 3/16 in root fairing to allow the curved rear root outline. Glue the strut fixings to the underside of the wing panels, flush with the ribs.

The lower centre section has a similar construction to the standard wing section with the addition of the grooved 1/4 x 1 in undercarriage support - cut slots in the ribs to house this support. Construction of the top centre section follows the same procedure..."

Supplementary file notes

Alternate version of the same plan (original layout).
Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

DH 60 Cirrus Moth (oz11723) by David Boddington from RCME 1985 - model pic

Datafile:
  • (oz11723)
    DH 60 Cirrus Moth
    by David Boddington
    from RCME
    December 1985 
    46in span
    Scale IC R/C Biplane Civil
    all formers complete :)
    got article :)
  • Submitted: 09/11/2019
    Filesize: 505KB
    Format: • PDFbitmap
    Credit*: RMC

DH 60 Cirrus Moth (oz11723) by David Boddington from RCME 1985 - pic 003.jpg
003.jpg
DH 60 Cirrus Moth (oz11723) by David Boddington from RCME 1985 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
  • DH 60 Cirrus Moth (oz11723)
  • Plan File Filesize: 505KB Filename: DH-60_Moth_oz11723.pdf
  • Supplement Filesize: 532KB Filename: DH-60_Moth_oz11723_alternate.pdf
  • Supplement Filesize: 895KB Filename: DH-60_Moth_oz11723_article.pdf
  • help with downloads
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2019.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.