Ascenda (oz11508)

 

Ascenda (oz11508) by Ray Malmstrom from Meccano Magazine 1965 - plan thumbnail

About this Plan

Ascenda. Simple rubber helicopter model.

Quote: "Build your own flying model helicopter from this design. Ascenda, by Ray Malmstrom

MODEL helicopters are fascinating, unusual flying machines and it is strange that so few designs. particularly rubber-powered ones, are available to aeromodellers. Therefore, this month, Meccano Magazine presents especially for you, a new helicopter design, the Ascenda.

Watching Ascenda fly vertically upwards, hover at a good height and then descend slowly as the power runs out, is a new kind of model flying that no other model aircraft can provide.

Although not a beginner's model, if you have a little aeromodelling experience, you should not find Ascenda difficult to construct and fly. Start construction with the rotor unit. Cut out the rotor head from 1/16 inch plywood and drill the centre hole to take a 20 swg wire shaft. Bend three wire rotor supports. Check and see they are all the same size. Next, bend the part that cements to the root of the rotor blades to the angle shown on the plan. Again check to see you have bent the same angle into all three supports.

Cement one rotor blade support wire to each arm of the rotor head. Using 1/2 inch wide thin tape or silk, fasten the wire supports to the three rotor head arms. Cement well and lay aside to dry thoroughly.

Cut three rotor blades from 1/16 inch medium grade sheet balsa. Sandpaper to section and attach the blades to the wire supports using tape or silk to fasten the wire securely to the blades. Check with the easi-build sketches, then lay aside to dry. Make the motor stick (pylon) as shown in the sketches. Bind the bearing block and the lower hook securely to the motor stick with thread and cement well.

Now, before proceeding, you must balance the rotor blades. Hang the rotor up and if one of the blades hangs down, add a very small amount of Plasticine to one or both of the other blade tips. Continue to balance the blades until all three hang perfectly level. This careful balancing is most important.

Assemble the balanced rotor unit to the top of the motor stick. The drive shaft is 20 swg wire. Note the two cup washers between the rotor head and the bearing block. Bend the end of the drive shaft over and lock the rotor head with a piece of tape or silk, cement well and allow to dry thoroughly.

Cut fuselage and tail boom from inch medium grade sheet and join together. Add the 4 inch diameter anti-spin disc, made from thin cartridge paper, to the end of the tail boom and then cement the fuselage unit to the motor pylon. The simple undercarriage is for display only. It fits in a slit cut in the base of the motor stick and is removed for flying.

Make up the rubber motor from a 42 inch length of inch wide strip rubber. Make this into three loops, approximately 7 inches long. Rub on rubber lubricant and install the motor between the hooks on the motor stick. Your Ascenda is now ready for flying, except for any decoration in ball-point pen or coloured felt markers, you may wish to apply. Do not dope your model!

Flying: Your Ascenda will fly either outdoors or indoors. For outdoor testing, choose some soft grass and a calm day. There are no glide tests with a helicopter, so holding the model in one hand by the motor stick, wind the rotor blades in an anti-clockwise direction about 70 to 80 turns. Then, holding the rotor with one hand, steady the model by holding the bottom of the motor stick and fuselage with the other. Now release the rotor and gently move the model vertically upwards and letting go, try and avoid tilting it one way or the other.

If your Ascenda topples over and falls to the ground, check the balance of the blades. This is important. If it fails to climb, but hovers at launch height, hold the rotor arms between the fingers and gently bend the root end of the blades to give a little more upward angle. Then try another flight.

The whole secret of successful flight, assuming the rotor blades are in balance, is getting the correct upward angle of the rotor blades. You can only find the best possible angle for a really good climb by trial and error, so do not be disappointed if your Ascenda does not shoot vertically upwards on its very first flight. Finally, you can increase the turns on your rubber motor to 140."

Direct submission to Outerzone.

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Ascenda (oz11508) by Ray Malmstrom from Meccano Magazine 1965 - model pic

Datafile:
  • (oz11508)
    Ascenda
    by Ray Malmstrom
    from Meccano Magazine
    June 1965 
    17in span
    Rubber F/F
    all formers complete :)
    got article :)
  • Submitted: 21/08/2019
    Filesize: 136KB
    Format: • PDFbitmap
    Credit*: Pilgrim

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2019.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.