Flex Wing (oz11505)

 

Flex Wing  (oz11505) by Unknown from Meccano Magazine 1968 - plan thumbnail

About this Plan

Flex Wing. Simple 'hang glider' style model.

Quote: "Why not build a flexible wing kite. A simple balsa model with kite/glider action, based on the same principles used to land space capsules and rockets.

HERE'S A model with a difference which you can build as a glider, or a power model - or even fly like a kite. In fact, it looks more like a kite than anything else, yet it makes a very stable free-flight model. One other advantage, it takes very little materials or time to make the model. You will need to scale up the plan full size on a sheet of paper about 18 in x 15 in to build the wing properly (or you can obtain a full-size plan from Meccano Magazine Plans Service, 13-35 Bridge Street, Hemel Hempstead, Herts, price 2s 6d post free). The plan as reproduced here is exactly one-half size.

Construction: Start by cutting out a piece of cellophane sheet to the dashed line outline shown on the plan. You can use clear or coloured cellophane, the latter giving a more interesting looking model.

Now cut the two leading edge spars to length and trim off one end of each at the angle shown on the plan (50 deg). Also cut the centre spar exactly 12-1/2 in long. All three spars are cut from 1/4 x 3/16 hard balsa.

Lay the cut-out cellophane shape carefully in posi-tion over the plan and pin the two leading edge spars down over the first position as shown on the plan. Make sure that the cellophane is stretched out taut without wrinkles. Coat one face of the centre spar with cement, lay down in position on the cellophane and hold this in place with a few pins. Now cement the overlapping strip of cellophane in front of each leading edge and smooth round the leading edge so that it is stuck in place. All three spars are now stuck to the cellophane panel.

Leave the centre spar still pinned down, but remove the pins holding the two leading edges down. Move these leading edges to the second position shown on the plan and pin down again in this position. This will, of course, cause the cellophane to slacken and wrinkle, but ignore this.

Cut the nose cap froms 1/16 ply to the shape shown and cement in place. Cut and cement the 3/16 x 1/8 spruce spreader in position and leave the assembly to set. Do not remove from the plan until this assembly has set quite rigid.

Cut the two 11-1/4 x 1/2 x 1/8 balsa side pieces, also the two struts from 1/2 x 1/4 balsa. The side view drawing shows how these side pieces are cemented on each side of the struts, and the angled ends of the struts are cemented to the centr spare of the wing assembly. Cement another piece of 1/2 x 1/4 balsa between the sides in front of the first strut to produce a solid nose to the fuselage. This about completes the glider model, except for cutting the fin from sheet balsa and cementing to one side at the rear, as shown.

Trimming for flight: The model should balance level when supported at the balance point shown (ie on the spreader). Add plasticine or similar trimming weight to get the balance point right. Then try hand launching the model. The cellophane covering will billow out and fill as the model is released and the model should behave just like any other glider. If necessary, adjust the amount of trim weight to get the best possible glide.

The model can also be tow launched. The approximate position for the tow hook is shown on the plan. Bend the tow hook from a paper clip and bind to the fuselage with cellulose tape for a start. If the model does not tow properly, try adjusting the tow position - moving it farther back if the model tends to weave, or forwards if the model simply pulls to one side. Once you have found the best position, bind the tow hook permanently to the fuselage with thread, adding a coating of cement over the binding.

Power conversion: To convert into a power model, cut off the fuselage nose short and cement a ply firewall to the front. Brace this with 1/2 x 1/4 balsa as shown in the detail sketch. The engine is then bolted directly to the firewall, but check first that the balance point will come out right. Shorten or lengthen the nose, as necessary, to compensate for the weight of the engine and still have the model bal-ancing on the spreader.

This size of flex wing is about right for an .ono engine. It is a little too small for safe flying with any-thing larger, so if you do want to use a bigger engine you should build a bigger flex wing. Build it in exactly the same way, but twice as big to suit an eaeo engine. You can use the same spar sizes, but this time use spruce instead of balsa. You can also beef up the fuselage sides if necessary, eg use 1/2 x 1/4 in balsa instead of 1/2 x 1/8.

Thin polythene sheet rather than cellophane will be better on larger models. This cannot be cemented, so you will have to use a slightly different technique for sticking the polythene panel to the spars. Lay the spars down first this time with the polythene panel on top and then pin down to the plan. Using a soldering iron, rub along the line of the spars to 'weld' the polythene to the balsa. This is quite easy to do, but do not use too much heat or you will melt the polythene. Then turn the wing over and complete welding the polythene overlap around the leading edges. Finally, pin down in the second position for cementing the nose cap and spreader in place."

Direct submission to Outerzone

Supplementary file notes

Article.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Flex Wing  (oz11505) by Unknown from Meccano Magazine 1968 - model pic

Datafile:
  • (oz11505)
    Flex Wing
    by Unknown
    from Meccano Magazine (ref:104)
    April 1968 
    16in span
    Glider F/F
    all formers complete :)
    got article :)
  • Submitted: 25/08/2019
    Filesize: 287KB
    Format: • PDFbitmap
    Credit*: Pilgrim

Flex Wing  (oz11505) by Unknown from Meccano Magazine 1968 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2019.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.