Slingshot (oz11486)

 

Slingshot (oz11486) by James Mears from American Modeler 1961 - plan thumbnail

About this Plan

Slingshot. Control line combat model, for .35 engine.

Quote: "Combat Winner. Slingshot, designed, built and flown in Texas by Texan James Mears.

Slingshot, a high-performance control line combat model, can fill your trophy case with something more than pipe dreams! It is a popular design, having won 3 first-, 4 second-, and 2 third-place trophies in seven area meets for the 'Lubbock Texans' club. At the Dallas Nats it was clocked at 102 mph pulling a streamer.

Even if you are not an experienced Combat man, this ship will give you speed and confidence. A hot mill up front is not too important until you have some 'wins' under your belt and are heading towards regional or national meets.

This simple 'fused-wing' maintains positive control under the most adverse weather conditions, yet has speed and snap in all maneuvers. The diamond airfoil and relatively high aspect ratio wing adds little drag and keeps the model solid on the lines. The stabilizer connects directly to the wing, intro-ducing a 1-1/4 in moment arm to the elevator hinge line. This eliminates the tendency of many wing jobs to shudder or stall in violent maneuvers. Twin rudders which skid on hard surfaces and serve as a point for streamer attachment impart a 'different' look.

Construction starts with the ribs. Shape as per plan; cut hard 1/16 x 3 x 36 in balsa down the center to form trailing edge halves. Mark rib positions on one of these. Lay bottom 1/4 in sq spar and bottom half of trailing edge on a flat surface. Cement ribs to trailing edge only - the spar merely keeps ribs in line for fore-and-aft positioning. Lay top half of trailing edge in place, use cement generously where trailing edge sheets meet. Hold trailing edge and ribs together with pins until cement sets. Cement bottom spar in place, then set assembly aside while cement dries completely.

Motor mount (F1) is maple or high grade plywood, 1/2 in thick (2 x 6 in is just right). I prefer solid maple, but if you can get aircraft or marine grade plywood, that's fine. The mount is slipped on the 1/2 in sq leading edge and pre-cemented to slip between center W1 ribs. Rudders are 1/16 plywood. Drill streamer holes and sand to a sharp edge. Stabilizer and elevator are hard 1/8 balsa. Do not sand stabilizer until it is fastened to wing - this way you get a smoother joint. Wing tips and tip braces are from same material as stabilizer and elevator.

When wing assembly is dry enough to handle, motor mount and leading edge are slipped in place and cemented. I use either Pactra C-77 cement or Elmers Glue here. Be sure mount is straight with no up- or down-thrust. If a tank is used, install it now, as the top spar wedges it in place..."

Slingshot, American Modeler, November 1961.

Direct submission to Outerzone.

Supplementary file notes

Article pages, thanks to RFJ.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Slingshot (oz11486) by James Mears from American Modeler 1961 - model pic

Datafile:
  • (oz11486)
    Slingshot
    by James Mears
    from American Modeler
    November 1961 
    39in span
    IC C/L
    all formers complete :)
    got article :)
  • Submitted: 23/07/2019
    Filesize: 252KB
    Format: • PDFbitmap
    Credit*: Circlip, RFJ

Slingshot (oz11486) by James Mears from American Modeler 1961 - pic 003.jpg
003.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2019.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.