About this Plan
Nebula. FAI Championship glider.
Quote: "Voted by general consent to be best finished A/2 at the team trials, this is one of the very few British glider designs for which a still air average of 2:30 can be claimed from 100 metre towline. Nebula, by Roy Yeabsley.
AN ACCIDENT can be said to have influenced this outstanding A/2 design, for it was evolved around the Danish drooped trailing edge idea. Ove Christiansen discovered the advantages of "flap effect" quite by accident through a constructional warp, and as reported in the December, 1953, issue, Hans Hansen used Borge Hansen's section with the droop incorporated to win the World Glider Championships. After correspondence with Borge on this flap idea, Roy Yeabsley made an A/2 with an adjustable trailing edge to find the best droop angle and after a considerable period of flying he designed his own airfoil with built-in droop and applied it to Nebula.
The results speak for themselves:
2nd place Pilcher Cup 1953 (309 entries) 16:35
1st place CMA Cup 1953 (35 entries) 8:30
3rd place K & MAA Cup 1953 (342 entries) 14:21
2nd place SMAE Cup 1954 (277 entries) 11:00
Here then is a contest glider of very top class, one that can be built easily, and if built carefully with a good finish, can match the best; but if made without due care and attention, all purpose is lost, and performance cannot be expected to be better than that of any other 'average' design. Being a relatively simple structure, full building instructions would be rather superfluous, but special attention should be paid to the following stages of assembly in order that no undue difficulty should arise.
Wings: are two-part for easier transport, retained by tongues in 1/16 sheet boxes, firmly bound with button thread and cemented. Make a tongue a 'free' fit as the boxes close in with use. Root ribs Nos.1-4 are not undercambered until boxes are fitted and wing finished. Build centre panels first, attach tips afterwards. Make TE slots for rib exactly 1/8 in deep and correct width. Excess cement used here only causes a warp. Front of the TE is packed up with a 1/8 sq balsa strip to conform with the airfoil section, otherwise all assembly is in the normal sequence of Leading Edge, TE, ribs, then spars. Cover with Lightweight Modelspan and while pinned down to board, give one coat of thin dope (70% thinners) on both surfaces. Two normal coats follow.
Fuselage: is a built-up structure with 1/16th sheet covering. Add auto rudder detail and some "fixed ballast" made from old flattened cement tubes before putting on the sheet, top and bottom being covered first to prevent lateral distortion. Last thing on is the noseblock. Cover over-all, including the simple tail unit, with Lightweight Modelspan water-shrunk and given three coats of dope.
Balance point is 50% of the root chord, and the hook position on plan is as it should be. If your Nebula weaves one way only, the hook is too far back. Weaving both ways indicates a forward hook, and the intermediate 'straight' tow position will be found midway between these symptoms. All flight adjustment to the model should be carried out with rudder trim and tailplane trailing edge packing."
Scan from DBHL, cleanup by rchopper56.
Direct submission to Outerzone.
Note supplement alternate plan scan (thanks to algy2) is unscaled and has hatched background. As printed in the pages of Aeromodeller, 1954.
Supplementary file notes
Article, thanks to algy2.
Alternate plan scan.
Did we get something wrong with these details about this plan (especially the datafile)?
That happens sometimes. You can help us fix it.
Add a correction
Do you have a photo you'd like to submit for this page? Then email firstname.lastname@example.org
User commentsNo comments yet for this plan. Got something to say about this one?
Add a comment
* Credit field
The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.
This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.
© Outerzone, 2011-2019.
All content is free to download for personal use.
For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.
Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.