Blow Bug (oz11287)

 

Blow Bug (oz11287) by Roy Clough from Air Trails 1953 - plan thumbnail

About this Plan

Blow Bug. Free flight sport model, with centrifugal 'pressure jet' IC fan system.

Quote: "A Basic Free Flight Pressure Jet You Can Build. Blow Bug, by Roy L Clough Jr.

Here's one modeler's answer to the coming age of all-jet flight.

This turbine jet model is somewhat unique in that it belongs to the pressure jet category rather than to the ducted fan class with which most model turbine jet experiments have been made. Instead of an axial flow fan mounted within a tube to accelerate a flow of air, this model uses a centrifugal impeller to pump its fuselage full of pressure to supply a nozzle with air for reactive propulsion.

We chose this configuration for two reasons; first because of its extreme simplicity, second because we wished to introduce something newer in the line of turbine jet models: while quite a bit has been done with ducted fans, this is the first pressure jet job we know of.

While theory gives the ducted fan an edge, on paper, practical considerations tend to favor the pressure jet. It does not require round sections, take-apart fuselages, tricky constructions or difficult starting or servicing procedures. It is also easier to mount the intake in a position which minimizes sucking up debris. (If you have never nosed over a turbine jet model in a snowbank or gravel pit, you have no idea how horrible life an get.)

Blow Bug is, therefore, a simple straightforward basic model with accent on serviceability and a performance margin that insures good results to those who have never built this sort of thing before.

Begin construction with the fuselage. As with any sheet balsa job, careful attention to wood grades will pay big dividends in performance. Use a light, yet strong grade of balsa. To insure a good fit at the hatch, build up the cen-ter part of the fuselage first, cementing the bulkhead and the crosspiece upon which the front of the wing rests to the sides to give a starting place. The bottom section of the fuselage is partly covered with 1/16 or 3/32 plywood for the engine bed, and this is braced at the corners with 3/16 sq bearers. Study the plan and note how the sliding hatch goes it place. This is a very simple deal, but a snug fit is essential to minimize air leakage, and to hold the hatch in place when the motor is running.

Sheet up the top and bottom of the fuselage, except at the wing station, then bend the front inward as shown and cover this portion. Wetting the wood may help the bending job, but we didn't find it necessary on the original. Be sure the inside diameter of the tail nozzle is 3/4 sq. This dimension is quite important for good performance.

The wing is a simple glider-type sheet balsa affair which is cemented into the fuselage. Any small openings which show as a result of dihedral angle should be cement-skinned over. Fair in the turtle-back with stiff paper and fit the hatch and scoop arrangement to the model at this point. Allow the cement to set for a few hours and then fuel-proof the inside of the model by pouring clear Sta through it and sloshing it around. Do not omit this step because otherwise an untreated inside will pick up a surprising amount of weight from oil absorption, enough to change the flight trim to tail-heavy after a couple dozen flights.

Make up the tail surfaces and attach, noting that the front of the stabilizer not cemented in place yet. No offsets are required since the gyroscopic action of the blower tends to bank the model to the right as it climbs - provided all surfaces are true.

Next mount the engine, taking Care to align the shaft centered with the blower diaphragm opening (that 1-5/8 hole in the hatch). Mount the tank at one side with the filler at the front for easy fueling with the blower in place. (The original model used an Infant Torp tank with a Wen-Mac engine giving a good run, but not too long.)

Don't let construction of the blower, or centrifugal impeller which is the heart of the system worry you. Just cut a disk of .025 stock and solder the blades in place using a good flux. Be sure to do a good soldering job, since a blade coming off could wreck the model. With a good job the blower is safe at any speed a small engine can spin it. We have used a number of such blowers, many of them turning much faster than this..."

Blow Bug, Air Trails, August 1953.

Direct submission to Outerzone.

Supplementary file notes

Article pages, thanks to RFJ.

Corrections?

Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Blow Bug (oz11287) by Roy Clough from Air Trails 1953 - model pic

Datafile:
  • (oz11287)
    Blow Bug
    by Roy Clough
    from Air Trails
    August 1953 
    36in span
    IC F/F
    all formers complete :)
    got article :)
  • Submitted: 05/06/2019
    Filesize: 279KB
    Format: • PDFbitmap
    Credit*: Circlip, RFJ

Blow Bug (oz11287) by Roy Clough from Air Trails 1953 - pic 003.jpg
003.jpg
Blow Bug (oz11287) by Roy Clough from Air Trails 1953 - pic 004.jpg
004.jpg

Do you have a photo you'd like to submit for this page? Then email admin@outerzone.co.uk

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment

 

 
 

Download File(s):
 

Notes

* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.

Scaling

This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.

 

Terms of Use

© Outerzone, 2011-2019.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.