Super Coupe II (oz11197)


Super Coupe II (oz11197) by Bob Cording from Model Airplane News 1973 - plan thumbnail

About this Plan

Super Coupe II. Radio control sport model, for 60 power. Uses the Ugly Stik wing.

Quote: "Fun-Fly your bag, something different as well, then why not try our uniquely constructed, thin plywood multi-bird? Lots of wing area, .60 power and lightweight all combine to make this an outstanding plane. Supercoupe II, by Bob Cording.

Would you like a plane for fun-fly contests that will give you an edge? How 'bout one rugged enough to stand almost every weekend flying for more than a year, with no apparent wear? Craving a plane that looks different but flies well? Need a plane that is relatively inexpensive and easy to construct? Always wanted to fly to Acapulco with a blonde model? Build a Supercoupe II! (four out of five ain't bad!)

With almost 800 square inches, .60 power and less than six pounds of flying weight, this plane will make it tough on your opponents in fun-fly events. After the construction portion of the article you'll find some legal (I think) tricks which can make you even more competitive in contests.

This craft was empirically designed. 'Empirical' means I didn't know any theory so it was all trial-and-error. A plane for fun-fly events should have good climb performance (keep it light), good low speed characteristics (light with a big wing), high speed ability (strong engine plus low drag), consistent spin performance including flat spins (big rudders with lots of throw), and quick ground handling (trike gear with wide mains).

To achieve all the above, Supercoup II uses a modified Ugly Stick (oz5175) wing joined with a light-weight rolled 1/32 plywood fuselage. Large twin rudders with 400 throw in each direction make it spin.

CONSTRUCTION: Wing: The easiest way is to buy an Ugly Stik wing kit (Jensen), then modify it for low wing service. The modifications are simple: Sheet the center section with medium soft 3/32 balsa top and bottom as shown in the plans to provide extra strength for those fun-fly touch-and-go landings. Cut 3/32 off the ribs under the sheeted area before gluing the ribs in place. A couple of Top Flite landing gear blocks (two for 50c, what a bargain!) are glued and braced behind the lower main spar doubler. If you will glue these blocks up in the wing about 1/8, ie not flush with the bottom sheeting, the covering will he smoother. The main gear has about a two-foot track which makes it almost impossible to ever drag a wing-tip.

I made new ailerons out of 1/4 in thick balsa, but if you like scallops you can use the ones in the kit. Don't change the kit wingtips, though. I think they are the secret to the anti-stall characteristics. The wing is held on with four 1/4 in nylon bolts. This is much more reliable for long term flying as it completely avoids the problem of looseness and vibration at the front connec-tion. The bolts go through the wing structure and screw into hardwood blocks tapped 1/4-20 which are glued inside the fuselage. The wing trailing edge needs only a couple of 1/16 plywood pads to take the bolt load but the leading edge requires insertion of two 1/8 plywood plates for strength. It is important to angle the rear tapped blocks so that the bolt heads hit the wood pads squarely. (A little touch-up with a Dremel tool will take care of minor misalignment.)

A neat trick for installing pin-type hinges in balsa is: Drill two 1/8 holes in each hinge half for better adhesion. Cut slits in wood with knife and smear hinge and slits with Titebond glue. Assemble, wipe off excess glue, and let dry 24 hours. Any glue that got into the hinge pin area will pop off when the hinge is flexed, leaving the surface free of drag. (Remember how bad it was the last time you got epoxy in the hinge?)

Fuselage: The fuselage has two major parts: (1) the 'box' which holds engine, tank, radio, and wing; (2) the 1/32 plywood which covers the box and goes back to the tail. The box must be constructed square and true. All the rest of the alignment depends on this..."

Super Coupe II, MAN, July 1973.

Direct submission to Outerzone.

Supplementary file notes

Article pages, thanks to RFJ.


Did we get something wrong with these details about this plan (especially the datafile)? That happens sometimes. You can help us fix it.
Add a correction

Super Coupe II (oz11197) by Bob Cording from Model Airplane News 1973 - model pic

  • (oz11197)
    Super Coupe II
    by Bob Cording
    from Model Airplane News
    July 1973 
    62in span
    IC R/C LowWing
    all formers complete :)
    got article :)
  • Submitted: 16/05/2019
    Filesize: 735KB
    Format: • PDFbitmap
    Credit*: Circlip, RFJ

Super Coupe II (oz11197) by Bob Cording from Model Airplane News 1973 - pic 003.jpg
Super Coupe II (oz11197) by Bob Cording from Model Airplane News 1973 - pic 004.jpg

Do you have a photo you'd like to submit for this page? Then email

User comments

No comments yet for this plan. Got something to say about this one?
Add a comment



Download File(s):


* Credit field

The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.


This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.


Terms of Use

© Outerzone, 2011-2020.

All content is free to download for personal use.

For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.

Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.