Buzzard II (oz11155)
About this Plan
Buzzard II. A 48 inch wingspan tailless sailplane.
Quote: "Buzzard II, by CS West.
IN order that this unusual model may give a consistent performance it is desirable that the flying surfaces should be in accurate alignment and that the weight of each wing should be exactly the same.
Pod and Fin. The pod or fuselage is built first as a frame sof 3/16 by 3/16 balsa which may have to be steamed or have slight nicks cut on the inside of the curves. No strength will be lost with the last mentioned procedure as the sides of the frame are next covered with 1/16 sheet balsa. The spar of the fin is then cemented in position at the rear 'end and the ribs and edges fitted while the pod is lying on one side. The fin ribs may be fitted as strips which are sanded down to section after the cement has hardened. Plywood ribs which have been drilled for the wing dowels are now cemented in position on either side. A piece of lead 2 in by 1 in by 3/16 in, is now cut out and should weigh about 2 oz. This is folded around the nose and held in place with a small countersunk nut and bolt. The corners must now be filed and rounded off until the fuselage balances at a point 4 in from the front (without wings). Further trimming will be effected when the macfuine is complete by adding lead shot.
Wings. The wings are built by usual methods but great care must be exercised especially when covering to prevent 'warping or inconsistency of any kind. First make two thi n plywood templates for the largest and smallest ribs. Clamp these together with the spar notches lined up and drill two holes 1/16 in dia to receive the wires on which are threaded .the required number of pieces of wood to make ribs for one wing. Then with a template on either side the whole lot are carved and sanded down to shape. The spar notches may be cut before removal from the wire. On assembly, the leading edge . must be blocked up to give the required wash in at the tip. The tubes which receive the dowels protruding from the fuselage are wound on a piece of dowel of like diameter and may be either sheet celluloid or brown paper.
Covering. The elevator tabs must not be covered as an uncontrollable warping may take place. Rag tissue is advised for the wings and fin applied very evenly and given one coat of clear dope.
Tow Hook. The tow hook is formed from 16 swg wire and cemented in place as shown. Improved line stability may be obtained by using twin hooks situated on the leading edge of the wings at half span and a 'Y' shaped towline. Full sized plans are available, price 2/- (see third scale reproduction opposite) from the Aeromodeller Plans Service, The Aerodrome, Stanbridge, Beds. "
Buzzard, Aeromodeller, August 1948.
Direct submission to Outerzone.
Supplementary file notes
Article pages, thanks to RFJ.
Did we get something wrong with these details about this plan (especially the datafile)?
That happens sometimes. You can help us fix it.
Add a correction
Do you have a photo you'd like to submit for this page? Then email email@example.com
User commentsNo comments yet for this plan. Got something to say about this one?
Add a comment
* Credit field
The Credit field in the Outerzone database is designed to recognise and credit the hard work done in scanning and digitally cleaning these vintage and old timer model aircraft plans to get them into a usable format. Currently, it is also used to credit people simply for uploading the plan to a forum on the internet. Which is not quite the same thing. This will change soon. Probably.
This model plan (like all plans on Outerzone) is supposedly scaled correctly and supposedly will print out nicely at the right size. But that doesn't always happen. If you are about to start building a model plane using this free plan, you are strongly advised to check the scaling very, very carefully before cutting any balsa wood.
© Outerzone, 2011-2019.
All content is free to download for personal use.
For non-personal use and/or publication: plans, photos, excerpts, links etc may be used, provided that full and clear credit is given to Outerzone with appropriate and specific direction to the original content i.e. a direct hyperlink back to the Outerzone source page.
Unauthorized use and/or duplication of this material without express and written permission from this site's owner is strictly prohibited. If we discover that content is being stolen, we will consider filing a formal DMCA notice.