Spacer

 

Comment:

Username:

 

 

Note: All comments are moderated before publication. Thank you for your patience.

 


 

Spacer  
by Sal Taibi
from Model Airplane News
December 1954
66in span
Tags: IC F/F Pylon
:) all formers complete

This plan was found online 23/12/2011 at:
http://www.rcgroups.com/forums/showpost....
A backup copy has been saved on Outerzone as:
PlanID: 2099 | Filesize: KB
Credit*: R Friestad www.co-op-plans.com
Format:  •PDFbitmap

Plan file details

Spacer. A-B Spacer. Free flight power model. Quote: "Winner in really big way is the Class AB job shown here for .19's to .29's. It's the best design published since the Civy Boy. The Spacer, by Sal Taibi. The AB Spacer was designed in January, 1953 and since then has compiled a terrific win record of 22 first places that year, mainly in the California area. Among some of the contests won were the following; Bakersfield, Calif., first place, Class A, 35 minutes 29 seconds ( AMA Record); San Dimas, Calif., first place, Class B-ROW ( AMA Record ); 1953 Nationals at Willow Grove, Pa., first place, Class A, Senior; Fresno, Calif. Annual Contest sweep of both Classes A and B; Los Angeles, Calif., first place, Class A, All Pacific Coast Championships; Long Beach, Calif., first place, Class A-B Junior-Senior-PAA Load, using a slightly widened and deepened fuselage to accommodate payload man, stock otherwise. The Half-A Spacer held both Open and Junior AMA Records in 1953. F. L. Swaney, Long Beach, Calif., 26:54, Open; and D. Farnsworth, Jr., Bakersfield, Calif., 20:02 in Junior Class. The Spacer has the good flying consistency that makes a contest winner, is a simple model to construct and extremely rugged and lightweight, averaging 24-26 oz. It will take most of the .19-.29 engines. Pin the two lower longerons on the top view of the plans, then cement all the bulkheads in place except the plywood bulkhead. Allow to set at least a half hour and then cement the top longerons and the 3/16 sq pylon supports in place; next cement the motor mounts in place and then the 3/16 x 3/8 rear stab longerons. When cementing the stab longerons together at the rear of the fuselage use a square, place it against the lower longerons and then pin the upper stab longerons together while against the square to assure proper alingment. After this has dried cement a piece of 3/8 x 1/2 balsa at the rear of the fuselage. Cement the 1/4 sheet together for the pylon, let set, and then, after sanding, trace the correct outline on the sheet balsa, cut out and then slide the pylon into the slot in fuselage. Remove the construction from the board, drill the motor mount holes, place the tank in position and fasten with wood screws. The tank must be in the position shown on the plans or the fill and overflow tubes will interfere with the timer shut-off installation. Remove tank temporarily..." Update 21/10/2018: Added article, thanks to Pit. Update 22/10/2018: Added supplementary plan file called 'tail 1', thanks to Pit. This is extracted from the drawings on page 10 of the article. Shows all tail parts. Now scaled up to fullsize. Update 22/10/2018: Added supplementary plan file called 'tail 2', thanks to rchopper56. Quote: "Hi Steve and Mary, I started to draw up the missing stab using the stab layout in the article. I then checked the area and it did not match the area of 182 sq inches posted on the main drawing. Then increased the span until 182 sq. inches was achieved. The attached PDF file is full size. Gene"

  


 

Spacer - plan thumbnail image